Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator wasn't cooling.
I checked the compressor and it was running. Next I removed the doors amd screws that held the divider strip. Next removed the bottom of the freezer to expose the evaporator fan. Removed the fan and checked it out with volt ohm meter. Discovered the fan motor was out. Ordered new one on line and received thenext delivery day. Insatlled in reverse of disassembly. When I plugged it in everything worked fine. Thanks for the quick delivery. You provided fine service. Sincerely, Joe Sutphen
defrost drain tube freezing up and stopping circulating fan motor
shut down power- removed plastic covering in refrigerator -installed new part- This has been installed for about 1 week and as of today every thing is working fine. This problem would occur about every 1-2months. So I will not really know for sure until some time goes by
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the grommet facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!
freezer compartment worked fine but very little cooling going to refrigerator section.
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The replacement part# matched the original. I attempted to contact PartsSelect but there was no response back.
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Frige evaporator fan became noisy then quit working & frige compartment became warm
Came home one evening and found the refer compartment evaporator fan making a noisy/grinding noise. While waiting for the part to arrive the motor finally quit working and the frige lost its ability to cool, but the freezer still worked fine. This is the fan that is inside the frige between the refer & freezer compartments - NOT the fan motor that is located in the bottom/rear next to the compressor. This grinding noise sounded like it was coming from inside the frige and could be easily heard under the vegetable trays and above the freezer compartment. To access this motor you need to go after it from inside the bottom of the frige compartment - there's NO need to remove the refer door. Pull the vegetable trays and remove the small phillips head screw located down in the lower air flow groove toward the front of the refer. Next, pry up & out the front white trim piece that runs the width of the frige. Once that piece is removed you can lift & slide back the whole lower frige trim/tray. Now lift out the large foam block compartment and you'll have complete access to the evaporator fan motor and the evap coils. Simply pull the fan motor assy out, still attached to the triangular bracket and disconnect the electrical pigtail. Next, pull the fan blade straight off the front hub, split & disassemble the motor bracket, & replace both fan motor grommets. Reverse the steps to reassemble the fan motor to the bracket and reinstall back in the bottom of the frige and plug in the electrical pigtail - the fan should (quietly) fire off instantly and begin the cooilng process. Reinstall the foam block, lower frige tray, front trim piece, reattach the phillips screw, close the door, and give it some time - it took our frige overnight to completely cool down. This is not a tough job, I spent more time figuring out how to access the motor then the actuall replacement. Hope these steps help to speed up your repair! And remeber Red Sox 4 Life!