Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GA283

GA283 Maytag Washer - Overview

Get Parts and Repair Help for GA283

If you know the washer repair part you need, you can browse the list of all parts on the GA283, or you can search by name or part description. You can also find your part by where it is located on the GA283 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for GA283 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$23.66

Water Inlet Valve

This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.

Order within the next 8 hrs and your part ships today!
$50.48

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

Order within the next 8 hrs and your part ships today!
$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 8 hrs and your part ships today!
$21.63

Syphon Break Elbow Kit with Clamp

For drain hose 7/8".

Order within the next 8 hrs and your part ships today!
$21.71

Damper Pad Kit

This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.

Order within the next 8 hrs and your part ships today!
$48.36

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Order within the next 8 hrs and your part ships today!
$26.35

Siphon Break Connector Kit

This plastic siphon break comes with a metallic clamp and gasket. It is used with many washing machines.

Order within the next 8 hrs and your part ships today!
$24.15

Glide and Spring Kit

This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.

Order within the next 8 hrs and your part ships today!
$5.15

Tension Springs -Set of 2

This is a set of 2 tension springs.

Order within the next 8 hrs and your part ships today!
$43.71

Upper Outer Tub Cover Clamp Kit

This clamp does include the nuts and bolts to hold it together but it does not include the rubber seal. Sold separately.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 410 of 420 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 226 of 118 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Cold water valve only opened to a trickle

  • Customer: Brian from El Cajon, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 165 of 173 people found this instruction helpful
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off... read more