Models > FWX433RBT5

FWX433RBT5 Frigidaire Washer - Overview

Get Parts and Repair Help for FWX433RBT5

If you know the washer repair part you need, you can browse the list of all parts on the FWX433RBT5, or you can search by name or part description. You can also find your part by where it is located on the FWX433RBT5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for FWX433RBT5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.06

Drive V-Belt

This belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$17.91

Water Inlet Valve

This washing machine water inlet valve has two ports for water to enter.

$33.09

Washer Lid Lock with External Safety Switch

Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).

$8.75

Tension Idler Pulley

This idler arm assembly comes with the pulley wheel.

$4.62

Leveling Leg

Sold individually. This part is used to adjust the height and keep the appliance level.

$46.50

Tub Seal Assembly

This seal helps prevent any leaking around the transmission of washing machines.

$15.15

Drain Hose

This part comes with a ninety degree elbow.

$5.50

SCREW

$61.18

Remote Style Pump with Motor

Use this with either a top load or front load washer. This pump has an horizontal mount.

$26.95

Agitator Drive Block

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replace broken drive belt

  • Customer: rodney from fairfield bay AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 173 of 196 people found this instruction helpful
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run... read more

Noisy spin cycle

  • Customer: Patrick from Humble TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 89 of 111 people found this instruction helpful
1) Unplugged washer and disconnected the hot and cold hoses.
2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer an... read more

washer continued to fill to point of overflow

  • Customer: alvaro from east hampton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 47 of 53 people found this instruction helpful
FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTI... read more