Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FWX223LBS6

FWX223LBS6 Frigidaire Washer - Overview

Get Parts and Repair Help for FWX223LBS6

If you know the washer repair part you need, you can browse the list of all parts on the FWX223LBS6, or you can search by name or part description. You can also find your part by where it is located on the FWX223LBS6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for FWX223LBS6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$5.42

Screw-In Plastic Leveling Leg

Sold individually.

$99.81

Drain Pump - 120V 60 Hz

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, whi...

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.

$9.33

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell...

$48.20

Tub Seal Assembly

If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace your old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.

$6.55

SCREW

Sold individually.

$6.23

SCREW

$12.81

Drain Hose

This drain hose is designed for use in your washer. The function of this part is to carry water from the drain pump to the house drain. If your washer is leaking or will not drain,...

$22.37

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace the snubber ring. Because the snubber ring is located under the tub of the washing machine, you will need to remove the front panel to access it. To protect your hands when removing the snubber ring, consider using a bent coat hanger or a sturdy wire with a hook to pull the old snubber ring free. Be sure to disconnect the power and water sources for the washing machine before you begin this repair.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replace broken drive belt

  • Customer: rodney from fairfield bay, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 221 of 246 people found this instruction helpful
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run... read more

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 132 of 162 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes l... read more

Noisy spin cycle

  • Customer: Patrick from Humble, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 107 of 131 people found this instruction helpful
1) Unplugged washer and disconnected the hot and cold hoses.
2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer an... read more