Models > FWT647GHS0 > Instructions

FWT647GHS0 Frigidaire Washer - Instructions

All installation instructions for FWT647GHS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FWT647GHS0
61-75 of 267
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing machine wouldn't drain or spin. It would run through its cycle, but only agitate.

  • Customer: Jen from Lebanon OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
Use a cup to take the water out of the washer. Get at least three large towels -- you're going to have to sop up the water when you disconnect the hoses.

Take the bottom panel off (2 Phillips head screws). Drain pump is on the right side.

Remove the two screws holding the pump to the metal bottom plate. Use a small socket wrench and/or a screwdriver. I had to use a screwdriver on the right screw and a socket wrench on the left screw! Place as many towels in the cavity as you can to catch the water that's going to come out when you detach the hoses.

There is an inlet hose and an outlet hose, attached with bright green clamps. Remove those with pliers. Clean up the water that drains out. The hose in the back (inlet) has a "coin catcher" area. Clean this out.

Attach the hoses to the new pump. Screw it down. Replace the bottom panel.

Water valve not shutting off correctly

  • Customer: Eric from Sebastopol CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

Quickly fixed a dumb mistake.

  • Customer: Andrew from McFarland WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
After accidentally dropping a crystal clock (don't ask) near the open door of the front-loading washer, the plastic striker broke and couldn't be repaired. Without this part being functional, the washer won't start because the door can't be secured.

I ordered the new part, and it arrived quickly -- that's really the story here.

Replacing it meant removing two screws, pulling the damaged part off, slapping the new part in, and replacing the screws. My 4th grade daughter could have done this one -- wish they were all that easy!

I'm glad the part came so quickly. With a local supplier, it would have taken four more days.

space

  • Customer: Alvin from Woodside NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 5 of 8 people found this instruction helpful
1. replaced (2) shocks, remove bottom cover 2. (1) spring and rib belt, used a wooden block to hold up drum , rolled out ld belt and rolled in new----remove top and rear covers after replaced same ---thanks..

Tank would not stop filling.

  • Customer: John from Willis TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Replaced both the water inlet valve and the tank pressure switch to eliminate any possible cause. The repair was easy, and now the washer works fine.

Washer wouldn't spin clothes

  • Customer: Brian from Forest Ranch CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
First thought the problem was with the spin cycle, however it soon became clear it was the pump that wasn't draining the water that kept the spin cycle from doing it's thing. After hand-wringing a large load and shopvacing out the remaining water, I ordered the new pump, got it in two days, and did a quick change out and it works perfectly. During the removal of the rubber boot that connects the tub to the pump, the one thing I did discover was a yucky buildup of years of fabric softener which I couldn't break my wife from using. But, after showing, and more importantly, letting her SMELL the fungus/mildew in the sludge, I've finally broken her of the habit! Best bang for the repair buck so far.

broken timer knob

  • Customer: Anne from Costa Mesa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Unscrewed the broken knob. Screwed the new one one. Voila

over filling

  • Customer: eliot from fairbanks AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

The washer would not pump the water out of the drum before the spin cycle.

  • Customer: Sven from Durand MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
First of all unplug your washer from the power supply and turn off the hot and cold water supply. I removed the front lower panel of the washing machine with a philips head screwdriver. Next I removed the plastic pins holding the right side shock obsorber. This was a little difficult because the upper pin is in a tight location and there's not much room to push the pin out. I just used the flat end of a screwdriver and slid it in place. The pins take some effort to push out, mainly because you have to hold the little tab on the pin down while you push it out. The replacement shock seems to be better constructed. I just put a little Vaseline on the new pins to help them slide through the metal sleeves on the ends of the shock. You also have to pay attention to which way the sleeves go into the shock so you don't push them out when you install the shock.

Replacing the pump was pretty easy. The pump is right there in front fastened to the bottom plate with two philips head screws. Have some towels ready, because if there's water in the drum or hoses it's coming out when you remove the hoses. Take a pair of pliers, or channel locks and open the hose clamp on the big inlet line, coming from the drum and slide it back so you can remove the hose. Then do the same for the outlet hose on the left side of the pump. It's easier to do this before you take the pump off the bottom plate. Once the hoses are off, remove the pump with a philips head screwdriver. While you have the pump out of the way, feel around inside the square reservior at the bottm of the big inlet hose to make sure there's nothing in there that might get stuck in the pump. A large bobby pin had made it's way into my pump and damaged it. It had fallen back down in that reservior, so at first I couldn't understand why the pump wasn't working, til I found it in there. Insatllation of the new pump is just reverse of disassembly. After that turn your water supply back on and plug in power. You might want to cycle the machine before you put the front cover back on to check for leaks. Good luck!

Kenmore 417.41042000 Front loading washer shakes

  • Customer: Chris from Burtonsville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!

20 cents in nickels destroyed pump. Pump vibrated violently afterwards.

  • Customer: Mark from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 3 of 4 people found this instruction helpful
1. Removed bottom cover - torx driver and drill adapter.
1.5 Unplugged machine and disconnected electrical supply to old pump.
2. Removed flexible hoses with wrench.
3. Removed pump base from machine with torx driver - the hard part as small hands are needed
4. Connected new pump to machine base with torx driver - hard again.
5. Connected hoses - wrench
6. Connected electrical supply and plugged in.
7. Tested pump - very quiet again.
8. That's it! Don't pay a service guy $250 to do this. Buy the pump and do it yourself!

old pump was viberating so bad that the whole machine rattled

  • Customer: Ed from Irrigon OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Very easy, took off the lower front cover (two screws). Pump is on the right side up front. Took the two screws out that hold it down, unclamped the clamps inlet and outlet hoses. Put a towel under and around pump to catch water befor pulling pump out. Installed the new one in revers order.

leaking water inlet valve

  • Customer: Steven from Oklahoma City OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve was made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.

Washer would function for 2 to 3 minutes and then pause. "PAU" appearing on the display.

  • Customer: Stephen from Amarillo TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Apparently the faulty switch was causing the washer to think that the door was open which would pause the wash cycle. The temporary fix was to disconnect/reconnect the door lock/switch assembly, thereby resetting the switch. Eventually though, the switch had to be replaced. The repair was simple. Unplug washer from power. Remove the metal band and spring from around the perimeter of the door seal. (I had to use needle-nose pliers for this step). Loosen the rubber seal near the door latch area only. Remove old latch by unscrewing the two screws, and disconnect all wired connections. Reconnect wired connectors using the new part and screw back on to the washer using the two screws. Reseat the rubber door seal and hold in place using the metal ring and spring you removed in the first step. Plug washer back in to power. That's it.

Door strike broke

  • Customer: Chris from Vernon Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!
All Instructions for the FWT647GHS0
61-75 of 267