Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FWS1339AC0

FWS1339AC0 Frigidaire Washer - Overview

Get Parts and Repair Help for FWS1339AC0

If you know the washer repair part you need, you can browse the list of all parts on the FWS1339AC0, or you can search by name or part description. You can also find your part by where it is located on the FWS1339AC0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for FWS1339AC0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$5.42

Screw-In Plastic Leveling Leg

Sold individually.

$99.81

Drain Pump - 120V 60 Hz

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, whi...

$9.33

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operating, you might need to replace the tension idler pulley. The tension idler pulley works in conjunction with the drive belt, so you might need to replace the belt as well as the pulley. Once the old pulley has been removed from the washer, you will need to transfer the spring and bushing from the old pulley to the new one before re-attaching it to the washer.

$48.20

Tub Seal Assembly

If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of th...

$6.55

SCREW

Sold individually.

$6.23

SCREW

$81.95

Dual Action Agitator

$72.17

Water Valve - 115V

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$43.60

Drain Hose

This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before placing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replace broken drive belt

  • Customer: rodney from fairfield bay, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 221 of 246 people found this instruction helpful
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run... read more

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 132 of 162 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes l... read more

Clicking due to agitator dogs slipping

  • Customer: BRIAN from UPLAND, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 78 of 95 people found this instruction helpful
One bolt (after removing the fabric softener dispenser and a water tight cover you will see it). Remove the bolt and slide it straight up and then it's the reverse to put in the new one. Very simple repair and very inexpensive if you willing to do it yourself. read more