Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FTF530FS3

FTF530FS3 Frigidaire Washer - Overview

Get Parts and Repair Help for FTF530FS3

If you know the washer repair part you need, you can browse the list of all parts on the FTF530FS3, or you can search by name or part description. You can also find your part by where it is located on the FTF530FS3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for FTF530FS3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.70

Door Strike

The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks, or the...

$44.98

Shock Absorber Kit

This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.

$76.18

Door Lock and Switch Assembly

This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock ...

$5.36

Screw-In Plastic Leveling Leg

Sold individually.

$30.53

Single Spring with Insulators

$103.98

Drain Pump - 60Hz 120V

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$6.11

SCREW

$6.36

SCREW

Sold individually.

$15.49

Drive Belt - 6 ribs

$41.91

Drain Hose

This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before placing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Door Catch

  • Customer: Joy from Columbia, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 516 of 516 people found this instruction helpful
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done. read more

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 386 of 452 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. read more

Both vibration shock absorbers broken

  • Customer: Douglas from Medical Lake, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 152 of 160 people found this instruction helpful
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went w... read more