Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FSE748GFS0 > Instructions

FSE748GFS0 Frigidaire Dryer - Instructions

All installation instructions for FSE748GFS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FSE748GFS0
376-390 of 481
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dryer did not heat.

  • Customer: Michael from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the great instructions that were provided by Partselect. There were no surprises. I took my time and it now works like new.

dryer tripped the circuit breaker

  • Customer: donald from belmont, VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected the dryer; cleaned the duct. I reconnected everything and started it up again and within seconds tripped the breaker.Decided probably the thermal limiter was faulty, so ordered new one from you. After it arrived I watched video, then removed the top and front, pulled drum to give me some workroom, replaced the limiter, reassembled in reverse order.I then reset the breaker, plugged the dryer in. Runs perfect.The drum was a challenge - so I used a wooden wedge to support from the front and opened the 12 by 12 rear port to access and reset the pulley cable assembly.

need knob

  • Customer: LINDA from LONGWOOD, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
buy need knob

Broken rotary knob

  • Customer: Shannon from San Juan Capistrano, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Easy peasy! It is as easy as lining up the knob with the D shaft on the dryer. There is a small piece/ring around the shaft that can still be stuck up inside so if you can't get the knob to sit flush with the dryer, peak inside and slide it off with a pair of pliers (the repair video shows this clearly if you need an example). I was done in 2 minutes, including the time it took to open the package!

Squealing after dryer running 20 m inutes

  • Customer: Charles from Flagler Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.

Rear drum bearing failure

  • Customer: TonyMac from Alamo, TN
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum

  • Customer: Witly from Wheatley Heights, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I remove the drum, and install the bearing just like the instructions in the video.

Drum Squeeking

  • Customer: Mark from Aurora, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Replace the Drum Bearing and Shaft

Removing old felt and glue

  • Customer: Gerald from Battle Creek, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the old drum glide there was tufts of felt and glue left behind. The DIY video (which inspired me to try this repair myself) says to use a scraper and wire brush to clean the drum edge. I decided to try a drill with a wire wheel. Worked great. The surface was shining clean in minutes.

Dryer Would Not Heat

  • Customer: John from Hummelstown, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

dryer started to squeal when started

  • Customer: Niel from Howell, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

squeeking & thumping noise

  • Customer: Thomas C. from Manahawkin, NJ
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Machine was not starting

  • Customer: Lorena from Sanger, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slowly my dryer began to stop worftking. I found myself wiggling the starter knob to make it work until it completely gave up. I took the model name and number and found a video describing how to replace the starter device. it took me about 20 minutes to make the change. it only took that long because I decided to clean out the interior thoroughly with a vacuum. All in all it was very easy.

Scraping noise at rear of drum

  • Customer: Bruce from Roscoe, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

Dryer not heating up and shutting down

  • Customer: Alan from Raritan, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.
All Instructions for the FSE748GFS0
376-390 of 481