Models > FRT17G4BW9 > Instructions

FRT17G4BW9 Frigidaire Refrigerator - Instructions

All installation instructions for FRT17G4BW9 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRT17G4BW9
76-90 of 228
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

one of the support rails on my deli drawer broke

  • Customer: Jennifer from Tully NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
first i removed the screw from the back of the shelf then pulled the old rail off. I sliped the new rail onto the post then replace the rear screw.

coil Iceing up

  • Customer: Thomas from Stuart FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

The drawer support rail was broken

  • Customer: Chevy from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I unscrewed the old drawer support and screwed the new one in. It was very simple!

freezer worked frig was warm. Ice maker is still not working

  • Customer: steve from Kirkland WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

Drawer rail under top shelf broken

  • Customer: Sandra from Standish ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
It was easy. I handed it to my husband.

Plastic drawer support had broken from extended use.

  • Customer: William from MIAMI FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
This was a truly easy snap-in repair. Because I live in a small fishing village on the coast of Venezuela, the only difficult part was waiting for the part to arrive. I'm very grateful that Part Select makes ordering parts easy and reliable.

Cheese drawer rail broke

  • Customer: Richard from Lancaster PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I took out the screw and removed the old rail, then I used the same screw to install the new rail. It took me 2 to 3 minutes. Very easy.

Door Shelf Missing

  • Customer: Lori from Idaho Falls ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered and replaced

Drawer support was broken

  • Customer: April-Lynn M from Berrien Centere MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Repair was quite easy. Simply remove screw and replace part. My repairman charges a min. fee of $99 to come by. I did this myself and saved an easy $100! The part came very quickly--next day after I ordered it. Would definitely do this again.

drwr. suppt. broken-- cracked

  • Customer: Melvin from THIBODAUX LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
took off bad part-- 1 screw-- took every bit of 3 min. to change

shelf guard broken (the fastner)..

  • Customer: James R. from Fayetteville AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Open the door and slide on the part. No Tools required

Frost in freezer, fridge not cold

  • Customer: Bob from Pinole CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

Door shelf bin fixture broke off

  • Customer: Cathleen from Potomac MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
This was the easiest thing to repair in my house! All I needed to do was to snap the appropriate new shelf in the place where the prior piece was and we were back in business. A caveat to anyone else who might try it-get your Mfgr/model number straight as well as measure the length of the shelf to be replaced. Since my brand was not listed in the pull-down menu for replacements, the first time I ordered the shelf replacement piece, I ordered the shelf that looked exactly like the one I was replacing however the replacement was a few inches too small! Thank you PartsSelect for an easy return policy and your guidance when I called

broken meat drawer

  • Customer: gene from pensacola FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
new drawer was received within 2 days and was extremely simple to install.

Support rail for meat drawer broke

  • Customer: Megan from Hamden AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Super easy. We unscrewed the broken rail, and screwed the new rail into place. Much easier than expected!!! We were also pleasantly surprised to have the part arrive the day after we ordered it!
All Instructions for the FRT17G4BW9
76-90 of 228