Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FRS6R5ESBL > Instructions

FRS6R5ESBL Frigidaire Refrigerator - Instructions

All installation instructions for FRS6R5ESBL parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6R5ESBL
76-90 of 747
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken actuator-water

  • Customer: Wesley from New Smyrna Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 11 people found this instruction helpful
Easy repair, except the re-install of the entire water/ice part back into the door. The original plastic water line too short to fit back into the small opening. Hint: Go buy 10 inch of new water line and a small connector. Run the new line up through the small opening, and connect to the original water line with the small connector. This made it easy to replace and test, and then cut of the excess water line.
Thanks.

2 broken shelving supports

  • Customer: Victor from Wilton, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 11 of 11 people found this instruction helpful
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

loud crack when fridge door opened past 90 degrees

  • Customer: Barry from Spring valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 11 of 11 people found this instruction helpful
Unscrewed screw holding plastic clip on right hand top hinge. Unfasten two lags screws holding right hand top hinge. Lift door off bottom hinge. (Do not unfastened bottom hinge) Remove old plastic bearing and replace with new. Repeat aforementioned instructions in reverse order. DOG EASY.

It Was Fast And Easy, No To Mention Affordable.

  • Customer: Jim from Herington, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 14 people found this instruction helpful
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

The ice/light buttons were cracked and broken

  • Customer: Thomas from Schwenksville, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 14 people found this instruction helpful
First of all, I ordered in the afternoon and the part was on my doorstep the very next day, amazing shipping. I shopped all over and this was the best price by a few dollars. I hope I never need any other parts, but if I do, I will come back to buy my parts here.

I pried the old cover off with a pocket knife and carefully installed the new one. Now it looks great and it only took me about 5 minutes.

evaporator coil would freeze up solid. no air flow through coil; no cooling.

  • Customer: KEVIN from BRONX, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 16 of 26 people found this instruction helpful
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.

Refrigerator light was out

  • Customer: andy from Peshastin, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 20 people found this instruction helpful
Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

Broken Fan Blade

  • Customer: Albert from Bristol, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 12 people found this instruction helpful
Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Light Socket short

  • Customer: Rebecca from Gautier, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 18 people found this instruction helpful
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

The bottom refrigerator door shelf bin broke.

  • Customer: Dan from Brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 12 people found this instruction helpful
The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

Water leaking from back of refrigerator

  • Customer: Barbara from Bryan, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 12 of 16 people found this instruction helpful
Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

Broken shelf support studs and crisper drawer cover.

  • Customer: Timothy from Mount Wolf, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 13 people found this instruction helpful
No problem, I Just pushed the plastic pin to the old support studs into the frig wall using a small screw driver and hammer and with pliers pulled the studs out to the wall of the frig being careful not to damage the wall. Then with pliers {needle nose} pulled the plastic pin out of the wall. Pushed the new support studs in the hole and tapped the plastic pin with a small hammer into the support stud. Replaced crisper drawer cover and glass shelf. Easy fix

water actuater arm broke at bend.

  • Customer: carlos from new bern, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 13 people found this instruction helpful
Very easy. I at first misunderstood the instructions. the fridge door remains closed. You pull out the water catch tray "outside" the door. someone said ice tray, thats why i thought i had to open the door to fix it. there are 3 screws that the water catch hides. once removed the control panel comes off which unplugs from bottom easily. then there are screws behind the control panel just removed. after those are unscrewed the rest tilts enough that u can uncrew the little metal bands that hold the arm. replace arm & reverse your efforts & your done. took less then 10 minutes.

Needed a new freezer door bin

  • Customer: Linda from Leesburg, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 10 people found this instruction helpful
One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

Refrigerator quit running

  • Customer: Frederic from Daytona Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 19 people found this instruction helpful
I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.
All Instructions for the FRS6R5ESBL
76-90 of 747