Parts That Fix Frigidaire Refrigerator FRS6LR5EM2 Noisy
Noisy is a commonly reported symptom for the FRS6LR5EM2 Frigidaire Refrigerator, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FRS6LR5EM2 Frigidaire Refrigerator that will fix Noisy. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of plastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.
Sold individually. This cam is located at the bottom of the fridge/freezer door.
The evaporator fan motor (Motor Evaporator Fan, Evaporator Fan Motor Kit, Evaporator Fan Motor, Refrigerator Evaporator Fan Motor) circulates air through the food compartment for efficient cooling in refrigerators. The evaporator fan motor can squeal as its bearing dries out. The motor bearings can totally seize, preventing any movement. The motor coil can also burn out, preventing any fan movement. If this motor fails, the refrigerator compartment will warm up and eventually the freezer will reduce cooling as well. Excessive frost can build up on the evaporator coil due to lack of air movement. The motor can make a squealing noise when it is beginning to fail or will not operate at all when powered, and this is a sign it should be replaced. The evaporator is located in the rear of the freezer compartment. This part measures 2-1/2 inches wide by 3 inches tall by 1 inch thick, at its widest point. It is constructed of plastic and metal, and comes in black/silver. This kit includes the evaporator fan motor and harness.
Sold individually.
This is a genuine condenser fan blade, which works with refrigerators, freezers and wines and beverage coolers.
This part allows the cold air from the freezer section to be aired into the fresh food section and it is controlled by the thermostat.
This door bin (Bottom Door Bin, Refrigerator Door Bin, Door Shelf Bin, Refrigerator Door Bin) is a movable bin mounted on the inner door to hold food items, bottles, and jars. Over time, a cold refrigerator can cause plastic to become fragile and break down. This can lead to other issues in the refrigerator. When the door bin will not hold securely onto the inner door panel, it must be replaced. This door bin measures 5.75 inches high, 16 inches wide, by 4.25 inches deep and is made of white plastic. Sold individually.
This OEM cup filter is designed to be compatible with all rear-filter refrigerators made before April 2001. The filter fits into a round white plastic housing. For this repair you may also require the PS428513 wrench or PS428532 O-ring. To install you will need to unscrew the cup before you can see the old filter, and then dump the water. Pull the old filter straight down and place the new filter inside the filter cup. The end of the filter with the O-ring should be directed upward. As you tighten the filter it will align itself. If your refrigerator has a Change Filter light, it will need to be reset. Press and hold this button until the green light flashes (up to 15 seconds). This filter has a 2-Inch depth, 4.25-Inch height, 2-Inch width and needs to be replaced every 6 months of use or 200 gallons depending on which comes first. Filters for: Taste and odor Sediment 99.3% of Lead 99.99% of Cysts 99.7% of Turbidity 99.8% of Particulates (Class I) 94.9% of Atrazine (a herbicide) 94.2% of 2,4-D (a herbicide) 97.8% of Chlorine (Class I) 87.5% of Toxaphene (a pesticide).
This is the replacement hinge kit for your refrigerator. This kit contains both the left and right hinges. Each hinge is made mainly of metal and plastic and is approximately 3 inches by 3 inches. This hinge kit does not contain the mounting hardware. The adjustable hinge kit supports the refrigerator and freezer doors and allows the doors to pivot open. The hinge kit also makes it easy to level the doors. This kit is a genuine OEM part sourced directly from the manufacturer.
This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.
This part is the replacement hinge bearing for your refrigerator. It is made of black plastic and is approximately 1 inch in diameter, and 1 ¼ inch in length. The hinge bearing connects the door panel and the door hinge and helps the door open and close properly. If you notice a clicking sound when opening or closing your refrigerator, or if the door won’t close at all, you may need to replace the hinge bearing. This part is sold individually and is an OEM part sourced directly from the manufacturer.