Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FRS6LR5EM2 > Instructions

FRS6LR5EM2 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LR5EM2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LR5EM2
106-120 of 805
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

housing-crusher was broken

  • Customer: Bob from Milton, WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
removed ice maker box and disassembled crusher unit on front of box and installed new housing.

evaporator coil would freeze up solid. no air flow through coil; no cooling.

  • Customer: KEVIN from BRONX, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 21 people found this instruction helpful
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.

Crisper support was broke

  • Customer: Ray from Millbrook, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 8 of 9 people found this instruction helpful
Parts Supply had a YouTube video to show it was done. This is one of the best sites to get parts there is. Easy to use, tells you how to install them easily. Thanks Parts Supply, I'll be back whenever I need a appliance part.

Food compartment not cooling, freezer working well.

  • Customer: Mary from Kenmore, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 16 people found this instruction helpful
Fantastic!
Sent in a brief description of problem and model number. Reply and description of other customers experiences guided us to the exact problem.
We ordered the part on Friday and it was here on Tuesday.
I prepared the freezer compartment for the removal of the old motor and on Sunday husband installed new Evaporator Fan Motor.

It works and is cooling like it did when it was new.

This has been a great experience as all repairmen wanted at least 60.00 to just come out and determine what the problem was. I can only imagine what the final bill would have been.

This was easy and inexpensive.

Thanks for all the help.

bins have been broken for several years

  • Customer: William from Spokane, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 10 people found this instruction helpful
The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.

lighting hit the house

  • Customer: keith from villa rica, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 19 of 44 people found this instruction helpful
first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts

Lightning struct the house and fried the evap thermostat

  • Customer: charles from parker, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 8 of 11 people found this instruction helpful
Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

Broken Door Bin

  • Customer: Peter from Whittier, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Item shipped Insanely Fast, ONE DAY.
Item was installed in 15 seconds, faster than it took me to remove it from the box!

ice dispenser paddle broke off

  • Customer: Emanuel from Coconut Creek, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
Remove power from refrigerator. Pull out the drip tray below paddle. Removed the 3 screws behind tray. Gently pull control panel out and remove the ribbon cable plug from panel. Set panel aside. Remove three screws holding panel housing to door, then pull out housing slightly and disconnect harness plug behind left side of housing. Pull housing out 3-4 inches. Look at the way paddle tabs engage ice dispenser switch mechanism. Remove the left paddle hinge screw and plate and loosen the right hinge screws(these also hold the water paddle hinge) Remove broken paddle by pulling out from right hinge plate and down. Install new paddle under right hinge plate, engage new paddle tabs correctly onto dispenser switch, install left hinge plate and screw, then tighten hinge screws. Reconnect harness plug, reinstall 3 housing to door screws, reconnect ribbon plug to control panel and reinstall panel screws. Reinstall drip tray. Reconnect power to refrigerator and check operation of ice and water paddles.

Ice make does not fill with water

  • Customer: Amritpal from sacramento, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 8 of 11 people found this instruction helpful
I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

Ice maker malfunctioned

  • Customer: Myron from Tumwater, WA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 7 of 8 people found this instruction helpful
We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

door didn't seal good

  • Customer: jerimy from greenbrier, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

Refridgerator freezing food

  • Customer: Bob from Gilbert, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 30 people found this instruction helpful
Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

Support rail broke

  • Customer: Karl from Bellaire, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

Original gate broke at the swivel point

  • Customer: Charles from New Orleans, LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 12 people found this instruction helpful
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
All Instructions for the FRS6LR5EM2
106-120 of 805