Models > FRS6LF7JW3 > Instructions

FRS6LF7JW3 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7JW3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7JW3
46-60 of 680
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator would not go into Defrost

  • Customer: Robert from North Chesterfield VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 21 people found this instruction helpful
When I first noticed that my refrigerator coil was iced up, I read a little bit about the defrost cycle of a refrigerator. I decided to try replacing the least expensive parts first. First I tried the defrost themostat, it was a very easy repair. My coil still froze up after a couple of days. Then I learned how to force my fridge into a defrost mode (on a frigidaire you just click the light button in the fridge 5 times in under 6 seconds). Then I noticed that the defrost heater was not heating up...this repair was more difficult. You have to first remove the two shelves, bin, and tracks. Then you remove the back panel...4 screws. Then you have to take out a couple of screws and drill out one rivet on the drain pan and pull the drain pan out so you can get the defrost heater which snakes up through the coil from the bottom of the coil. Be careful, as the drain pan and coil fins are very sharp, I sliced a couple fingers messing around with these parts. The defrost heater itself is relatively easy to put in once the coil is in the right position (there are videos on youtube on how to do this). After I put in the new heating element, and buttoned everything back up, I was excited to check my work...I forced the fridge into defrost by clicking the light switch 5 times, and the heater still didn't come on! It dawned on me that this problem started about 5 days after a major power outage (hurricane Irene)...When the power came on, it must have surged, and zapped the defrost control board...Long story short, I replaced the control board (about $75.00 from partselect.com) and my problem is fixed...at least I have a 100% brand new defrost system now...Of course it won't be too long until my wife wants another fridge to match her Stainless Steel applicances...oh well, this one will do fine in the garage.

Filter neeed replacement

  • Customer: Nancy from Lawrenceville NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 15 people found this instruction helpful
Just opened the filter storage and popped out the old one and put in the new one. Ran the system for three minutes according to directions and it worked fine.

The bottom of Refrigerator would not get below 48 degress. Freeezer was working fine.

  • Customer: Jeffrey from Bridgeville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 17 of 28 people found this instruction helpful
First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.

No power to Ice and water dispenser

  • Customer: Carmelo from Howell NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 25 people found this instruction helpful
First removed the drip tray with a firm tug, Then removed the 2 screws to remove the trim, had to remove the board to get get to the connector. (there is a clip that holds the wire tight) connected the new ribbon cable and secured it with the clip, screwed the board back in and pushed in the other end of the cable. and screwed the trim back and the drip tray. surprisingly Very easy to do.

Ice Crusher Broke. Plastic in Ice Tray

  • Customer: Ronald from Dickson TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 26 people found this instruction helpful
Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

Water and Ice dispenser quit working.

  • Customer: James from Lakeland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 17 people found this instruction helpful
Turned off power at C/B panel. Took cover off dispenser, removed 3 screws, board held in by 4 screws. Removed all 4, replaced board after removing connecter. Put back together. Turned power on. Worked perfectly. 15 minutes max, part was $81, recieved 3 days after ordered.

Refrig door would not close automatically

  • Customer: Michael from Lithia FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 10 of 10 people found this instruction helpful
Replaced the plastic/nylon piece on the door. First, I remove the door hinge cover by unscrewing the one bolt. Second, unbolted the two bolts that hold the door in place. Third, lifted the door off the bottom hinge. Four, remove the bottom plate that is held in place by 3 screws. Five, using pliers move the old plastic piece from the bottom of the door. Six, press into place the replacement part. Seven, re-install the bottom plate. Eight, rehang the door on the bottom hinge. Nine, restall the top hinge and rebolt the two bolts that hold the hinge in place. Ten, reinstall the top cover. Finished.

ICE MAKER DOESN'T MAKE ICE

  • Customer: JANET from NEW FAIRFIELD CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 25 people found this instruction helpful
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

The radiator was not defrosting.

  • Customer: Alfredo from Mount Pleasant SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 19 people found this instruction helpful
The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.

Power outage for two days took out control unit

  • Customer: Jeffery from Nunica MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 20 people found this instruction helpful
take out screws front control panel ,then screws on left panel holding control unit. had to clean up plastic she got a little toasty. unhooked control unit replaced with new and reassembled. The real story is in your excellent web site easy to find exactly what I need and with prompt shipping, I was back in service quicker than having someone come out and repair.

Great Job
Jeff Baker

Husband Broke Water Dispenser Arm ;-)

  • Customer: Deanna from Cleveland Heights OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 11 people found this instruction helpful
Project requires removal of 9 phillips head screws. Also have some needle nose pliers and a paper clip and/ or skinny magnet handy for steps (7) and (9).

(1) Turn off power to refrigerator.
(2) Slide out water catch tray at bottom of dispenser unit.
(3) Remove the three screws that are now visible.
(4) Pull front water/ ice dispenser (cosmetic) panel off of the refrigerator and set aside.
(5) Remove the 3 screws affixing circuitry panel in place and set aside.
(6) Gently pull out the circuit panel and allow it to hang from the refrigerator door. Note: Unless you have very large hands you should not have to disconnect any wiring to do this repair.
(7) Remove the three screws and two plates holding the dispenser actuator in place, being careful not to drop the screws or plates into the unit. If they do drop you can get them out of the unit using the needle nose pliers and/ or a bent pointy piece of metal (e.g., paper clip).
(8) Remove broken dispenser arm.
(9) Insert new dispenser arm.
(10) Replace all screws and panels.
(11) Turn refrigerator power back on.

Note: The new dispenser arm has reinforcing bars molded into the back that were not on the original model. The company is apparently aware of the problem of the weak dispenser arm and fixed it in the replacement part... so, you should not have to be doing this repair again.

The bin on the refrigerator door broke

  • Customer: cora from glen allen VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 9 people found this instruction helpful
It was very easy. I attached to the socket.

drip from door water dispenser

  • Customer: Paul from Anderson IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 10 of 12 people found this instruction helpful
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

Freezer was cold but the fridge was warm. Back panel of fridge was building up frost

  • Customer: Albert from Buffalo Grove IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 15 of 27 people found this instruction helpful
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

damaged gasket refrigerator door

  • Customer: cletus from Godfrey IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
pulled old gasket out of groove in door. Put vaseline on slotted part of gasket that fits in groove of refri. door Put some vaseline on gasket surface that would be on the hinge side of door, so it would close with ease. Had no problems at all. Thanks

P.S. Sorry about not having the model No.
The Part No was PS1991324 Magnetic Gasket for Refr side of a Freezer/Refrigerator FRIGIDAIRE There are no screws to remove on this model. Just start at one corner and begin pulling old gasket out of the groove of the door.
All Instructions for the FRS6LF7JW3
46-60 of 680