Models > FRS6LF7JW3 > Instructions

FRS6LF7JW3 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7JW3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7JW3
31-45 of 680
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Interior light was on "red" indicating a water filter change was needed.

  • Customer: Tom from Simpsonville SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 17 people found this instruction helpful
Just pushed the button along side the filter and it popped out in my hand. I unpacked the new filter module and inserted it. It was necessary to run water through the dispenser for a couple of minutes to purge the air and clear the lines. The modular filter assembly is more expenseve than some but the ease of replacement makes the cost a good value.

No water flow to in-door water/ice dispenser

  • Customer: Richard from St. Louis MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 20 people found this instruction helpful
Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searches on the internet to finally figure this part out. From there on out it went smoothly. Old base came out with two screws. Reversed process for reinstall of new base. Water hoses just slipped back into place and locked themselves in. Just takes a little patience.

Water coming out of the ice maker when dispensing water from the door.

  • Customer: kyle from Palo Alto CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 22 of 32 people found this instruction helpful
This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

Water leak

  • Customer: Russell from Jacksonville AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 19 of 24 people found this instruction helpful
Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

ice maker cycling properly but not getting water on fill cycle

  • Customer: Terrance from Orland Park IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 16 of 17 people found this instruction helpful
1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

Light socket melted around bulb

  • Customer: William from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 21 of 33 people found this instruction helpful
After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.

bottom of frezzer cold...top warm...refrigerator warm

  • Customer: jim from galveston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 17 of 21 people found this instruction helpful
I first located the wiring diagram under right frt. of fridge. Using it I troubleshot the problem to be the ADC module. I ordered the ADC module and blower motor that it controls(as a precaution since that is the device that the ADC drives)After removing the icemaker and all the back panels in the freezer you can access the blower motor. The ADC module is accessible after removing the plastic panels in the top of the fridge. Look for a burn spot on the module. Be sure to order the parts using the fridge model # and not the parts # on the wiring diagram(they will have changed since the model was built). Mine needed an updated wiring harness and deleted one of the dampner motors. Be sure to replace one wire at a time so not to get confused of wire location. Pretty straight forward repair if you have some mechanical ability. I have never repaired a fridge before, but have done car electronic work.

The ice chute door didn't close all the timed

  • Customer: Shelby from Clinton IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 20 of 30 people found this instruction helpful
The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.

ice maker would not rotate out cube or crushed ice.

  • Customer: David from Ponca City OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 19 of 28 people found this instruction helpful
1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

The Upper Crisper Drawer Cover cracked in the Front

  • Customer: LAUREN from MADERA CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 16 people found this instruction helpful
Simply replaced the drawer cover (frame) of that shelf. Removed crisper drawer, removed glass shelf, removed frame, placed new frame in, then glass, then drawer. Very easy.

broken door shelf bin

  • Customer: Denise from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 17 people found this instruction helpful
Just snapped into place. Very easy.

the Auger would not augerate, I was not able to use the ice dispenser.

  • Customer: ESTEBAN from MCALLEN TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 26 people found this instruction helpful
It was very simple. I order the complete Ice Container with Auger. It is great that it is already assembled. I just took out the old one and slipped the new one in. It has been working great ever since. I am just sorry that I waited so long to order the part. It was already like four months that the Auger started to give out on me. Thank You for everything, especially the delivery time.

Refrigerator would not go into Defrost

  • Customer: Robert from North Chesterfield VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 21 people found this instruction helpful
When I first noticed that my refrigerator coil was iced up, I read a little bit about the defrost cycle of a refrigerator. I decided to try replacing the least expensive parts first. First I tried the defrost themostat, it was a very easy repair. My coil still froze up after a couple of days. Then I learned how to force my fridge into a defrost mode (on a frigidaire you just click the light button in the fridge 5 times in under 6 seconds). Then I noticed that the defrost heater was not heating up...this repair was more difficult. You have to first remove the two shelves, bin, and tracks. Then you remove the back panel...4 screws. Then you have to take out a couple of screws and drill out one rivet on the drain pan and pull the drain pan out so you can get the defrost heater which snakes up through the coil from the bottom of the coil. Be careful, as the drain pan and coil fins are very sharp, I sliced a couple fingers messing around with these parts. The defrost heater itself is relatively easy to put in once the coil is in the right position (there are videos on youtube on how to do this). After I put in the new heating element, and buttoned everything back up, I was excited to check my work...I forced the fridge into defrost by clicking the light switch 5 times, and the heater still didn't come on! It dawned on me that this problem started about 5 days after a major power outage (hurricane Irene)...When the power came on, it must have surged, and zapped the defrost control board...Long story short, I replaced the control board (about $75.00 from partselect.com) and my problem is fixed...at least I have a 100% brand new defrost system now...Of course it won't be too long until my wife wants another fridge to match her Stainless Steel applicances...oh well, this one will do fine in the garage.

Meat Drawer and Support Rails Broken

  • Customer: Mark from Colorado Springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 15 people found this instruction helpful
I pulled the shelf unit out and removed the screw that held in each side. The old rails removed easily and the new ones installed just as easily. I put the shelf back in and slid the new meat drawer in and it was done - much to the delight of my wife. Parts Select has a great website. It was my first time and I read one of these with the exact problem I was having. I ordered the parts, which came quickly. Everything easy and worked great! I'm a happy customer.

I broke the glass shelf when I took it out of the refrigerator to clean.

  • Customer: Carol from Sunrise FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 16 people found this instruction helpful
This occurred on Sunday and I ordered the part Sunday afternoon. By Tuesday afternoon the replacement was back at work. It just slipped into place, without any tools or fuss.
All Instructions for the FRS6LF7JW3
31-45 of 680