Models > FRS6LF7JS3 > Instructions

FRS6LF7JS3 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7JS3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7JS3
31-45 of 606
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker cycling properly but not getting water on fill cycle

  • Customer: Terrance from Orland Park IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 14 of 15 people found this instruction helpful
1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

Meat Drawer and Support Rails Broken

  • Customer: Mark from Colorado Springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 14 people found this instruction helpful
I pulled the shelf unit out and removed the screw that held in each side. The old rails removed easily and the new ones installed just as easily. I put the shelf back in and slid the new meat drawer in and it was done - much to the delight of my wife. Parts Select has a great website. It was my first time and I read one of these with the exact problem I was having. I ordered the parts, which came quickly. Everything easy and worked great! I'm a happy customer.

the door would not close on it's own

  • Customer: harry from bradenton FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 12 people found this instruction helpful
The parts came within 2 days. The delivery was great. I took the food off the door, then removed the top hinge. Lifted door off bottom hinge and laid the door on a blanket on the floor. I then had access to the closing mechanism top and bottom that is just two plastic cams that lift the door as it opens. The weight of the door then is used on the cams to help close the door with the appliance level. It was very simple and assembly was just reverse order.

Broken ice maker

  • Customer: Juan from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 18 of 30 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

Part of the ice actuator that activates the switch broke off thus not allowing the ice augar to work. By pushing to hard on the actuator trying to get ice we broke a corner off the dispenser module and had to replace it.

  • Customer: Jack F. from Clifton Springs NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 13 of 15 people found this instruction helpful
Turn off power to refrigerator. Remove dispenser tray and three screws. Lift up on cover and pull away from fridg. Next remove control circuit board, use magnetic screw driver on very small screws. Important to mark all wires and their location before removing. Remove water tube from water actuator by lifting tube out of actuator,you don't have to turn water off. Next remove dispenser module and set next to new dispenser module. Then carefully remove and install parts on new dispenser module. Take your time and besure all parts installed as they were on the old module.

The bottom of Refrigerator would not get below 48 degress. Freeezer was working fine.

  • Customer: Jeffrey from Bridgeville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 17 of 28 people found this instruction helpful
First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.

Light socket melted around bulb

  • Customer: William from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 26 people found this instruction helpful
After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.

Door had a poping sound when opening and closing

  • Customer: Ivan from Mountain Home AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 12 people found this instruction helpful
Removed the trim screw on top of the door then removed the two hinge bracket bolts. lifted the door
off placed on the table. Remove the two screws on
holding the bearing bracket on the bottom of the door.
removed the bearing and replace with the new one.
Reinstalled in reverse order.

ICE MAKER DOESN'T MAKE ICE

  • Customer: JANET from NEW FAIRFIELD CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 24 people found this instruction helpful
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

The Upper Crisper Drawer Cover cracked in the Front

  • Customer: LAUREN from MADERA CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 12 people found this instruction helpful
Simply replaced the drawer cover (frame) of that shelf. Removed crisper drawer, removed glass shelf, removed frame, placed new frame in, then glass, then drawer. Very easy.

the Auger would not augerate, I was not able to use the ice dispenser.

  • Customer: ESTEBAN from MCALLEN TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 21 people found this instruction helpful
It was very simple. I order the complete Ice Container with Auger. It is great that it is already assembled. I just took out the old one and slipped the new one in. It has been working great ever since. I am just sorry that I waited so long to order the part. It was already like four months that the Auger started to give out on me. Thank You for everything, especially the delivery time.

loud crack when fridge door opened past 90 degrees

  • Customer: Barry from Spring valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 10 of 10 people found this instruction helpful
Unscrewed screw holding plastic clip on right hand top hinge. Unfasten two lags screws holding right hand top hinge. Lift door off bottom hinge. (Do not unfastened bottom hinge) Remove old plastic bearing and replace with new. Repeat aforementioned instructions in reverse order. DOG EASY.

ice maker would not rotate out cube or crushed ice.

  • Customer: David from Ponca City OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 23 people found this instruction helpful
1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

Power outage for two days took out control unit

  • Customer: Jeffery from Nunica MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 20 people found this instruction helpful
take out screws front control panel ,then screws on left panel holding control unit. had to clean up plastic she got a little toasty. unhooked control unit replaced with new and reassembled. The real story is in your excellent web site easy to find exactly what I need and with prompt shipping, I was back in service quicker than having someone come out and repair.

Great Job
Jeff Baker

The radiator was not defrosting.

  • Customer: Alfredo from Mount Pleasant SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 12 of 17 people found this instruction helpful
The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.
All Instructions for the FRS6LF7JS3
31-45 of 606