Models > FRS6LF7JS0 > Instructions

FRS6LF7JS0 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7JS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7JS0
61-75 of 636
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Freezer was cold but the fridge was warm. Back panel of fridge was building up frost

  • Customer: Albert from Buffalo Grove IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 15 of 27 people found this instruction helpful
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

Ice Maker wasn't making ice

  • Customer: Robert from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 10 of 13 people found this instruction helpful
I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

Freezer worked great, refrigerator would not cool

  • Customer: Farrell from Atchison KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 10 of 13 people found this instruction helpful
Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help

The bottom refrigerator door shelf bin broke.

  • Customer: Dan from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 8 people found this instruction helpful
The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

bins have been broken for several years

  • Customer: William from Spokane WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.

Water leaking from back of refrigerator

  • Customer: Barbara from Bryan TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 9 of 12 people found this instruction helpful
Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

Too of the rail supports inside the fridge were broken

  • Customer: Kristen from Payson UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 8 of 9 people found this instruction helpful
First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!

water valve failure

  • Customer: Robert from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

Broken shelf support studs and crisper drawer cover.

  • Customer: Timothy from Mount Wolf PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
No problem, I Just pushed the plastic pin to the old support studs into the frig wall using a small screw driver and hammer and with pliers pulled the studs out to the wall of the frig being careful not to damage the wall. Then with pliers {needle nose} pulled the plastic pin out of the wall. Pushed the new support studs in the hole and tapped the plastic pin with a small hammer into the support stud. Replaced crisper drawer cover and glass shelf. Easy fix

Broken actuator-water

  • Customer: Wesley from New Smyrna Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
Easy repair, except the re-install of the entire water/ice part back into the door. The original plastic water line too short to fit back into the small opening. Hint: Go buy 10 inch of new water line and a small connector. Run the new line up through the small opening, and connect to the original water line with the small connector. This made it easy to replace and test, and then cut of the excess water line.
Thanks.

Had a broken door bin and shelf support stud

  • Customer: Amanda from Peachtree City GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 8 of 10 people found this instruction helpful
I pulled out the old support stud with a pair of pliers, pushed the new stud in, and gave it a few taps with the hammer to secure it in the fridge wall. For the door bin I just slid the new bin in place.

2 broken shelving supports

  • Customer: Victor from Wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 7 people found this instruction helpful
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

parts were broken, needed replaced...

  • Customer: Amy from Dunedin FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
I followed a gentleman's directions on your website, very useful I might add. It helped me replace all the broken parts with ease. I am a 33 year old mom of two. Anyone could do these repairs that I did. Thank you.

Water filter needed replacement

  • Customer: Glenn from Simi Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 13 people found this instruction helpful
Once I recieved the new filter, I enthusiastically opened the box, removed the filter from it's packaging and set it aside for quick access. I opened the refrigerator door, pushed the release button on the old filter and pulled it out. I then tossed the old filter in the trash.
Once that was done, I removed the 2 rubber caps covering the inlet and outlets on the new filter. Then, with ace precision, I guided the new filter back into the slot until it clicked. I ran the water for 3 minutes as the instructions suggested, then, had a glass of water.
Mission accomplished and it went off without a single hitch!

Glenn Walker, Simi Valley, Ca

Hinge bearing broke causing door to rub when opened

  • Customer: Corey from Brazil IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 13 people found this instruction helpful
I removed the screw in the plastic cover on the top of the fridge that covered the fridge side hinge first. Then, I removed the two nuts with a nut driver that hold the hinge in place. After removing the two nuts and the hinge, I lifted the door up and out of the bottom hinge and placed it on a flat surface. I used a pair of pliers next to pull out the broken hinge bearing from the bottom of the door itself. After removing the old bearing I inserted the new bearing in the door. Next, I put the door back on making sure the hinge went into the hinge bearing and put the door in the closed position. After that was all done and the door was set properly, I put the top hinge back on with the two screws and put the plastic cover back in place. Took 20min to complete. A second set of hands would have been helpful with putting the door back on, but it can be done by yourself.
All Instructions for the FRS6LF7JS0
61-75 of 636