Models > FRS6LF7GS4 > Instructions

FRS6LF7GS4 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7GS4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7GS4
106-120 of 623
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

support rail had broken lower slide

  • Customer: Betty from Hot Springs AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Could have done it with my eyes closed! Removed shelf and drawer, then removed broken support rail. Removed screw from broken rail and put the new, two piece rail together using that screw. Snapped rail back onto wall...returned shelf to fridge...returned drawer to fridge...returned myself to sanity! Yee Haw Easier than installing it was ORDERING IT. I was amazed by the ease of that process. Your ordering site is incredibly easy. By the way...I am a blonde and for blondes everywhere...Look at what I could do :)

Lightning struct the house and fried the evap thermostat

  • Customer: charles from parker CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

light switch did not operate correctly

  • Customer: Jeff from Lakeville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.

Switch would not allow door to close.

  • Customer: Charles from Front Royal VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Broke the actuator

  • Customer: Darwin from Delano CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
I unplugged the fridge and removed the dispenser's drip plate. There are 3 screws holding the front fascia. I carefully slid the fascia up to removed it. I unplugged it from what looks like a circuit board from the dispenser. Remove 3 more screws that held the board exposing the ice dispenser's hole and the water actuator. To give myself a little more room to work, I disconnected the board from the fridge. Attempted to removed the water hose but i couldn't, but found out didn't need to. I used a longer philip's screwdriver to unscrew two very small plates that were holding the actuator in place. Need a magnitized screwdriver for this, my hands are too big to reach in there. It took about 15 minutes. NO extra parts or additional parts to order.

broken door shelf bin

  • Customer: Raul from Kissimmmee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
put the new ones

The slide rail split on the meat drawer

  • Customer: Judie from Mendota Heights MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
All I did was remove the drawer, remove one screw. I took out the old slide, installed the new one and replaced the drawer. Quick and easy

Ice make does not fill with water

  • Customer: Amritpal from sacramento CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 5 of 8 people found this instruction helpful
I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

I broke the fan while cleaning the coil

  • Customer: Raymond from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
The broken fan made my refrigerator sound like a lawn mower I pulled the refrigerator out of it's nook and disconnected the power, removed the back panel with my battery powered drill motor, slid the old fan off of motor shaft, slid the new fan back on ran it to make sure the problem was corrected. The entire repair took less than fifteen minutes and was as simple as it could be. Please be careful when cleaning your coil, as the fan is easily damaged if you should contact it.

Guides damaged, crisper pan cracked

  • Customer: Darin from Nicholasville KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
1.Got on line to Partselect ordered the parts we needed .they arrived Quickly and in good condition 2.Except the tray was sent in error delaying the repair. 3.contacted Partselect costumer services for assistance 4.Followed their direction and reorder the correct one hoping the correct one would arrive .it did the next day .5.On to repair, removed broken stud with panel stud puller with the aide of a putty knife to spread the pressure of tool stud came out 6.reinserted new stud 7.replaced the new upper crisper drawer cover glass not included . 8.Upper Crisper pan to complete the repair. 9.all in all successful with the help of Partselect superior parts and helpful guides.

Refrigerator light was out

  • Customer: andy from Peshastin WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 9 people found this instruction helpful
Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

Refrigerator was not cooling

  • Customer: Vicki from Johnson City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

Refridgerator freezing food

  • Customer: Bob from Gilbert MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 27 people found this instruction helpful
Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

door didn't seal good

  • Customer: jerimy from greenbrier TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

I was cleaning the refrigerator and I accidentally dropped the insert

  • Customer: FERDINAND from AURORA CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
I just slipped it into place.
All Instructions for the FRS6LF7GS4
106-120 of 623