Models > FRS6HR45KS0 > Instructions

FRS6HR45KS0 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6HR45KS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6HR45KS0
1-15 of 588
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water from refigerator dispenser started tasting bad

  • Customer: Anthony from Springfield VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 324 of 325 people found this instruction helpful
I removed the top shelf in the fridge. I then unscrewed the cover to the water filter and pulled the filter cartridge down into the cover. Keep the cover upright as there may be some water in it. I carried it to the sink. I took the new cartridge and ran water through it from the sink, then set it in the cover and took it to the fridge. I pushed the cartridge up into the space that I removed the old one from and screwed the cover back on. Then I took an empty pitcher and filled it from the water dispenser in the fridge door. I did this three times to charge the filter and remove charcoal dust. Water tastes great now. I ordered two filters so I would ony have to buy once a year. Great site to order the filters from. Cheaper than other sources and delivery was quick.

Needed to replace water filter

  • Customer: Karen from Lowell NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 142 of 162 people found this instruction helpful
It was really easy. All you have to do is twist the old filter out, stick in the new one and twist!

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 121 of 125 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.

water leaking out of refrigerator

  • Customer: Jose from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 132 of 162 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 104 of 136 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and note which pipe you unclipped it from. Cut the wires on the old thermostat midway between the plugs and the sensor. Using the supplied butt connectors, strip the wire ends on color matched wires (should be a dark blue or black) and crimp them together. Repeat with the other wire. Discard the white shrink wrapping. I wasn't able to get it small enough with a hair dryer or lighter. Plug the thermostat back into it's respective plugs. Clip the thermostat back onto the pipe you removed it from. Replace the back panel with the four screws. Ensure the bottom of the panel is set inside of the drip tray. Replace any shelving you removed. Plug the refrigerator back into the wall. Your done!

broke two door bins, one on frig and one on freezer doors

  • Customer: Linda from Tierra Verde FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 122 of 192 people found this instruction helpful
We had the bins the next day. I had called some other companies and they wanted twice your price! You were much more curteous on the phone, much more professional and quicker and cheaper! I will tell everyone in Florida who to call if they need a part!
Thank you so much!
Linda Cecil

icemaker stopped making ice

  • Customer: David from New Bern NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 82 of 100 people found this instruction helpful
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

Water actuator broke

  • Customer: Jonathan from Universal City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 62 of 67 people found this instruction helpful
If you think you probably can't do this, you're like me... but you just had to try because you needed the part anyway right? This really was quite simple, a lot easier than it sounds from the description and saved me probably $75 I'd have had to pay a tech to do it. Just unplug fridge, yank that water spill tray out, yes yank, it's a bit hard to do that if you've not done it before. After that remove the 3 phillips head screws you just gained access to. Lift panel frame up then out. Disconnect wire harness plug and set that frame aside. Take out next screws exposed to free the unit. Tilt unit out and remove the two little screws and shims holding actuator in place. Remove broken one. Put new one in. Reverse all actions taken thus far. Plug fridge back in and have a drink of water like nothing ever happened. : ) You can do this!

"Paddle" on ice actuator broke off.

  • Customer: Ryan from Elk Grove CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 49 of 55 people found this instruction helpful
Slide off drip tray at bottom of ice/water compartment.

Remove the 3 screws along bottom edge of face plate. Slide face plate upwards slightly to disengage tabs holding top of face plate to fridge door. Pull face plate slightly away from fridge, reach behind plate, and disconnect wiring harness. Set face plate aside.

Remove 3 screws holding ice/water actuator mechanism to fridge door. Disconnect wiring harness on left side of actuator mechanism. This allows the left side of mechanism to swing outwards.

Looking down on top of mechanism, loosen the two screws holding the small, metal retaining plates for ice actuator. (The metal plates hold the ice actuator pivot pins in place in the actuator mechanism). Once the two screws are loosened, the metal plates can be moved to the side to free the ice actuator.

Remove old ice actuator and replace with new actuator. NOTE: Ensure the black ice door flap regulator (the thing with the gear teeth) stays engaged with the gear on the damping mechanism while installing the new ice actuator).

Move the metal retaining plates back in place over the ice actuator pivot pins and tighten both screws. Move the ice/water actuator mechanism back in place and re-connect the wiring harness on the left side. Re-install the 3 screws holding the entire mechanism in place.

Re-connect the wiring harness to the face plate and slide the tabs at the top of the plate into the holes in the fridge door. Slide face plate down and line up the 3 screw holes at the bottom of plate. Re-install the 3 screws. Re-install the drip tray. You're done!

broken door bin

  • Customer: Mitzi from Cedar Rapids IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 75 of 137 people found this instruction helpful
Just slid into place provided.

Refrigerator would sometimes freeze everything

  • Customer: donna from brandon FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 45 of 54 people found this instruction helpful
we researched the internet with our symptoms and most sites said it was the thermostat. At $800+ for a new refrigerater, we decided to order the thermostat. Found schematics on the net, the thermostat was located in teh freezer compartment . Unplugged, removed food from freezer, removed the bottom shelf in freezer, and the back panel It was EASY to find. Cut 2 wires, replaced with new thermostat. DONE! The new thermostat came with new connecters.

Water filter needed to be changed

  • Customer: Mark from Port St. Lucie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 28 of 33 people found this instruction helpful
I removed the filter casing containing the casing, removed the filter and replaced it with the new filter and screwed the casing in place tightening with the wrench.. It took less than 5 minutes and was the easiest replacement Ive ever done.

everything in refrigerator freezing even on warmest setting

  • Customer: Benny from astoria NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 30 of 39 people found this instruction helpful
To access the part you have to remove the back panel of the freezer compartment from the inside of the freezer itself. There are four screws to this panel. I emptied the contents of the freezer, took of 2 shelves and brackets to gain access and removed the cover. Located the part , cut the wires with a wire cutter and left a small tail ....MAKE SURE TO UNPLUG REFRIG OF COURSE ... the part is clipped on the coils , added the new part. matched the color wires and added the connectors , crimped the wires and added a little electrical tape and put the panel and shelves back. THE REFRIG IS WORKING LIKE A CHARM

Ice dispencer would not work

  • Customer: Richard from Bristol CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 25 of 30 people found this instruction helpful
At first I took our apart, and tried to fix the feed wheel. I did something wrong putting it back together because even though it feed ice, it would not crush ice. Less that a week later the whole thing jammed.
I really did not know what was wrong with the unit, so I was pleased to find an entire assembly for a lot less that an in-home repair would have cost. The part arrived early in it's estimated time table. I simply pulled out the old unit slid in the new, transferred the ice into the new unit and that was it. I was up and running, my wife was thrilled and I was a hero. THANKS!!!

The freezer door shelf fell off and broke

  • Customer: Tammy from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 22 of 25 people found this instruction helpful
This process was so easy. I put in the model # and saw the piece I needed immediately along with a picture of it that helped me confirm it was the right one. All I had to do is snap the shelf in when it arrived.
All Instructions for the FRS6HR45KS0
1-15 of 588