In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle. A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.
Running but not cooling off and frost in the back of the freezer
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and note which pipe you unclipped it from. Cut the wires on the old thermostat midway between the plugs and the sensor. Using the supplied butt connectors, strip the wire ends on color matched wires (should be a dark blue or black) and crimp them together. Repeat with the other wire. Discard the white shrink wrapping. I wasn't able to get it small enough with a hair dryer or lighter. Plug the thermostat back into it's respective plugs. Clip the thermostat back onto the pipe you removed it from. Replace the back panel with the four screws. Ensure the bottom of the panel is set inside of the drip tray. Replace any shelving you removed. Plug the refrigerator back into the wall. Your done!
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.
Water Dripping from through the door water outlet and Ice Maker doesn't make ice.
I had two problems, the first was that water was dripping from the through the door outlet and the second problem is that the ice maker wasn't making ice.
Replacing the water valve was a simple process:
1. Turn off the water to the fridge at the household shutoff valve. 2. Move the fridge away from the wall. 3. Unplug the mains power (AC) plug from the wall power outlet. 4. Remove the 5 screws with a nut driver that hold the cardboard backing off the refrigerator. 5. (This is a great time to vacuum off the coils and underside of the fridge.) Disconnect the water supply from household plumbing with a box end wrench or channel lock pliers. I kept a large plastic cup and rag handy for the left over water in these hoses. 6. Remove the two screws from the water valve bracket on the right hand side and pull the water valve straight back from the fridge and line up the new valve in the same orientation. 7. Remove all the color coded electrical connectors (3 of them) and attach them to the new water valve. 8. Remove the remaining water hoses and attach them to the corresponding connectors on the new valve. 9. Dispose of the old valve and reinstall the new valve in reverse order.
The problem with the ice maker not making ice was because water was flowing so slowly from the valve that it was stopping in the fill tube at the back of the freezer and freezing stopping all water flow into the ice maker. I pulled the fill tube out of the back of the freezer from behind by rotating it 45 degrees counter clockwise and pulling straight out removing the ice blockage and drying the fill tube before I reinstalled.
Since I replaced the valve I had to take the cover off of the icemaker and set the water fill level down (screw toward the minus sign) and then adjusted it by checking the ice after each time it dropped and increasing the fill amount by 1 full turn (roughly 0.7 ounces) until it was just enough to make fully formed ice cubes.
First I replaced the Defrost Thermostat on the coil and this did not fix the problem. So I ordered this new ADC (Adaptive Defrost Control)board. It is not identical to the first ADC board and at least one feature the old ADC did was deleted from the function of the Fridge. Not sure why? Because the board were different a new wiring harness was provided. Step 1. Unplug the unit and remove the water filter. Step 2. Remove the covers off of the unit on the top of the fridge using the 1/4" nut driver and a 1/4" deep well socket with extension for the deeper inset fasteners. This exposes the wiring harness and the ADC board as well as the temperature controls. step 3. Remove the screws for the ADC on the cover and remove the wiring harness from it. No need to note the wire's positions as the new ADC uses a different connector. step 4. As you remove each connection of the wire harness from the unit replace that connection with then new harness connector to eliminate any confusion. Do each one. One by one until the old harness is completely loose and the new harness is completely installed. step 5. Install new ADC which in my case was now enclosed in an orange case. Unlike the one I removed that was and open pcb. Step 6. Replace covers using the 1/4" nut driver and 1/4" wrench. Step 7. Replace filter and plug in unit.
Apparently there have been 4 versions of this ADC board through the years. My fridge was built in 2003 not long before I bought it.
First I disconnected the power cord, then removed the screws that held the bracket that holds the base for the water-filer in place. I then disconnected the water lines(intake and outflow). Next I removed the screws that held the water-filter's base in place. I then disconnected the release lock mechanism for the filter and finally removed the water-filter base. I did the reverse to install the new water-filter base. Previously I had tested the intake water line and noticed the water was flowing with enough pressure upto the water-filter's base but no water was exiting thru the outflow line, which leads to the Ice-Maker and Dispenser. I had tried changing the filter but that didn't solve the problem it was then I had realized that the Base was the problem. The actual problem was the spring-loaded valves for both the intake and outflow lines, which had a plastic prong that protrudes out of the base that is triggered by the filter when installed. The two prongs were worn-down so the filter wasn't activating the spring-loaded release valve to let the water thru. As for the light, I just unscrewed it.
water leaking(pouring) from the filter into the refrigerator
Pushed the button on the filter in the fridge, the cartridge popped out and in with the new. That simple. Prior to replacement the water was leaking, although it was still producing water and ice through the door. When the filter was out, no leaks, but no water and ice! Just needed a new filter.
At first I took our apart, and tried to fix the feed wheel. I did something wrong putting it back together because even though it feed ice, it would not crush ice. Less that a week later the whole thing jammed. I really did not know what was wrong with the unit, so I was pleased to find an entire assembly for a lot less that an in-home repair would have cost. The part arrived early in it's estimated time table. I simply pulled out the old unit slid in the new, transferred the ice into the new unit and that was it. I was up and running, my wife was thrilled and I was a hero. THANKS!!!
we researched the internet with our symptoms and most sites said it was the thermostat. At $800+ for a new refrigerater, we decided to order the thermostat. Found schematics on the net, the thermostat was located in teh freezer compartment . Unplugged, removed food from freezer, removed the bottom shelf in freezer, and the back panel It was EASY to find. Cut 2 wires, replaced with new thermostat. DONE! The new thermostat came with new connecters.
pulled fridge from wall, removed card board cover, unplug the fridge. turn the water off to the fridge. remove the water source from fridge first then remove 2 screws that hold the valve. then the wire plugs. hoses.. they were color coded.
The water dispenser/actuator broke and I wanted to replace it
First I pulled the fridge out and unplugged it. Then I removed the drip tray at the bottom of the water and ice dispenser. This exposed three screws that held the frame of the dispenser mechanism to the freezer door. I removed the three screws and lifted it up a little and I could pull it out and tip it to get at the inside of the dispenser mechanism. I could pull the whole mechanism out a bit, but I was afraid to pull it out too far for fear of unplugging something and tearing or breaking a wire. The water dispenser actuator piece has two round plastic "pins" on either side to allow the actuator to rock back and forth. These "pins" are held in place in a round channel by two metal plates which were in turn held in place by two screws. When I tried to take out these retaining plates, I dropped one of the screws in the dispenser mechanism. I had to fish it out with a magnet. By the way, the plates did not respond to a magnet, so when I dropped one of these, I had to use needle-nosed pliers to fish it out. It took a while, but I finally got the old actuator out and out the new one in and carefully re-attached the retaining plate with their respective screws and re-attached the little spring to the actuator. Before I put it back together, I cleaned off the little door to the ice dispenser. It looked a little crudded up and I just wiped it off with some damp Q-tips. I then put the dispenser mechanism back on to the freezer door, put the screws back, slid the drip tray back, plugged it in and it (surprisingly) works fine. Looking back, I probably should have bought a part for the ice dispenser, too, and replaced that at the same time.