Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FMV156DCG

FMV156DCG Frigidaire Microwave - Overview

Get Parts and Repair Help for FMV156DCG

If you know the microwave repair part you need, you can browse the list of all parts on the FMV156DCG, or you can search by name or part description. You can also find your part by where it is located on the FMV156DCG by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the FMV156DCG

[Viewing 4 of 4]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.41

Grease Filter

If you are having trouble cleaning out your grease filter, or if it is damaged to the point of no return, maybe it is time to replace it. The grease filter is a ventilator that tra...

$31.74

Relay Switch

The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capacitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..

$108.64

Door Handle

Screws NOT included.

$47.34

Waveguide Cover

$16.44

Light Bulb - 20W

This 20-watt lightbulb is most commonly found in the microwave. The lightbulb brightens the interior of the microwave while it is running so you can keep an eye on the food while i...

$34.24

Turntable Motor

This turntable motor is used in microwaves. This is what rotates the glass tray so that your food is heatied evenly. The specs for this synchronous motor are 120 Volts, 60Hz, 3rpm, and 2.1 Watts. It features two 3/16-inch male spade terminals, which is what attaches to the internal wiring of your appliance. The motor also includes mounting holes; there are two mount holes on either side of the part. This replacement motor is approximately two inches in diameter, and it is sold individually. Before you attempt this repair make sure you unplug your microwave.

$33.71

Door Latch

This black door latch enables the switches to make sure that the door is closed before it operates.

$133.25

Vent Grille - Black

This vent grille mounts on the top of the microwave above the door

$28.45

DAMPER ASSEMBLY

This is an exhaust damper assembly for a microwave, which is also known as a microwave vent damper. The damper directs air flow through the vent duct from the top or rear of your m...

$59.99

Glass Cooking Tray

The glass tray, used in a microwave, holds food plates and containers on it. The glass tray, also known as a turntable, rotates when the microwave is heating up food to ensure the plate of food is evenly heated. If your glass tray is broken, shattered, or is not rotating when heating, it is best to replace it for better heating results. The tray has dimensions of 33 x 35.6 x 2.5 cm and weighs 455 grams. Refer to the manual provided by the manufacturer for installation instructions and guidance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Timer would run but the microwave won't start

  • Customer: Tim from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 69 of 108 people found this instruction helpful
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up. read more

Broken Handle

  • Customer: Brent from Bend, OR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 38 of 53 people found this instruction helpful
Removed the retaining clip that keeps the door on, took the door off. Removed the plastic rim that is clipped into place. Removed old screws holding on handle and replaced. read more

Turntable stoped working

  • Customer: steve from New Bern, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 26 of 29 people found this instruction helpful
Removed the 3 screws to drop the lower panel and, removeed the turn table plate and ring. Then removed the 2 screws holding the motor, the 2 wires attached to the motor and removed the old motor.Replaced the new motor in the reverse order. DO NOT FORGET TO UNPLUG THE MICROWAVE FIRST. read more