This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and u...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely ...
This splash shield kit is used in dishwashers and is attached to the lower front corners of the tub. The splash shield is used to prevent water from spraying past the door seal. If your dishwasher is ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
February 13, 2023
Blue rotating sprayer wheel on lower arm fell off and melted on element
For model number FGID2466QF2A
Hello Steve, Thank you for your inquiry. For the model number that you have provided, we show the lower spray arm as part# PS11770610, the lower spray arm support as part# PS12712289, and the heating element as part# PS3653449. We hope this helps with your repair.
Hi I hit the delay button a few times to 11h.I thought it would cancel. My mistake. How do I cancel that?
Get back to the start.
For model number FGID2466QF2A
Hi Tawny, thank you for reaching out. To cancel the DELAY START option and to begin the selected cycle before the delay period is over, press and hold the START/CANCEL pad for 3 seconds. We hope this information helps!
Was this helpful?
Thank you for voting!
Tawny
June 14, 2023
Thank you for your first answer to my question.
The delay light is still on.
I held the start button down for 3 seconds & it still has not gone off?
The dishwasher ran its cycle. Which is fine.
For model number FGID2466QF2A
Hi Tawny, thank you for reaching out. First, try resetting the dishwasher. Unplug the dishwasher, wait 60 seconds, and then plug it back in. If the issue persists, then you may need to check the control panel, part number PS9865008, to solve this issue. We hope this helps!
There seems to be no power to the dishwasher. Control panel shows no lights. I have checked the circuit breakers and they are good. Is there a reset button somewhere on the dishwasher that might need resetting.
For model number FGID2466QF2A
Hello Horace, thank you for your inquiry. According to our research, your model does not have any reset button. You may need to unplug the unit for 1 minute and plug it in again and also check the power cord for damage. If it does not resolve the issue, then replace the electronic control board, part number PS12365809, to solve the problem. We hope that helps!
I have error code Uo for blower vent problem. Is there an entire blower vent part and the cost.
For model number FGID2466QF2A
Hello Lance, thank you for getting in touch. The part you are looking for is the blower vent assembly, PS12741853. It includes the entire vent part, and currently, it costs $114.19, which is subject to change. We hope this information helps!
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having th
... Read moree problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic
... Read moregroove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.