Models > FGHD2433KF1 > Instructions

FGHD2433KF1 Frigidaire Dishwasher - Instructions

All installation instructions for FGHD2433KF1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FGHD2433KF1
16-30 of 294
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Upper wash arm bushing had worn

  • Customer: Ronald from Montgomery TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 9 people found this instruction helpful
Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

loose spray arm

  • Customer: Doris from Arkadelphia AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
Unscrewed the old spray arm and replace with the new spray arm.

The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!

Heating element corroded, not heating

  • Customer: Denise from Burnt Hills NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 9 of 10 people found this instruction helpful
Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

Top spray arm separates from mount

  • Customer: Richard from Macclenny FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
unscrewed old spray arm, installed new arm. Took less than 30 seconds.

Broken upper sprayer

  • Customer: Bob from YONKERS NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!

Leaking water at the end of cycle

  • Customer: Joe from Prospect KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 18 people found this instruction helpful
Remove dishwasher from cabinet flip on it's back. Remove two wire connectors, two torx screws pull pump out and replace very simple. Parts select were great and very fast to ship parts

Dispenser door broken.

  • Customer: C from Covina CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.

Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.

Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..

Dishwasher Leakibng

  • Customer: Eric from Benton KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 7 of 8 people found this instruction helpful
Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks

found spray arm on the rack

  • Customer: JOHN from LA QUINTA CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
found spray arm on the rack looked at the top of rack saw a nut screw the nut looked at the clip found the ears broke off easy r&r.

Water leak underneath dishwasher

  • Customer: Richard from New Orleans LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 7 of 8 people found this instruction helpful
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

No water was coming into dishwasher.

  • Customer: Jeffery from Excelsior Springs MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 8 of 12 people found this instruction helpful
Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.

Spray arm came off in wash cycle

  • Customer: mike from Bartlett IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.

Arm-Control fell off

  • Customer: Dan from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
I unscrewed and removed the old Arm-Control fixture. I had a little (very little) trouble figuring out how to fit the gasket. It didn't go on like i thought it should. There was no gasket on the original fixture. So I put it on the way I thought it should go. I then screwed the new Arm-Control fixture on to the outlet. That was it. No tools required.

Upper spray arm fell/broke off

  • Customer: Sharon from Clinton Township MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
I researched the problem we had with our dishwasher and found the Parts Select website. My husband and I figured out how to remove the broken part and I selected and purchased the replacement.

The part was shipped quickly and when it arrived I changed the broken part with the replacement in less than five minutes. It seems to be working just fine.

I have added Parts Select to our "favorites" in case we have problems with any of our other appliances. Thanks Parts Select. :)

LEAKING FROM THE BOTTOM OF DISHWASHER

  • Customer: Kathleen from Hamilton NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 11 people found this instruction helpful
REMOVED SCREWS AND PUT NEW BOTTOM GASKET IN OLD ONE JUST FELL OUT.
All Instructions for the FGHD2433KF1
16-30 of 294