FGC355VW0 Roper Range - Instructions

If your stove work's but your oven won't get hot it is your ignigter the ignighter in proper working condition sends a signal to the gas valve saying let the gas flow its ok. When the ignighter quits working it won't let the gas flow and your oven will not get hot. It is an easy fix. Just pull out all of interior parts the racks and the bottom heat shield the ignighter the white stone looking part that is screwed to the burner with two wires and it really don't matter what way the wires go back one of the wires connects in the back so you will have to pull the oven out. Now you have to clean under it and your done.

Removed oven door and burner guard. Removed screws holding ignitor bracket and small panel beneath oven door. Disconnected ignitor wires behind panel and pulled out ignitor. Removed old ignitor from bracket and inserted new unit. Fed wires back down thru tubing and screwed in bracket. Connected wires and replaced panel. (Note: old ignitor glowed but would not pass enough current to operate gas valve)

Purchased 2 piece broiler pan from this site

Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.

1. ordered two new switches
2. installed switches
3. all ignitors work

Really appreciated the pictures of the parts--made selection very easy.

I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

very easy

Screwed in light bulb and glass protector

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.