Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FGB24L2ECA

FGB24L2ECA Frigidaire Wall Oven - Overview

Get Parts and Repair Help for FGB24L2ECA

If you know the wall oven repair part you need, you can browse the list of all parts on the FGB24L2ECA, or you can search by name or part description. You can also find your part by where it is located on the FGB24L2ECA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for FGB24L2ECA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$31.10

Temperature Sensor

The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit yo...

$6.40

Light Bulb

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the internal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.

$34.07

Rack

$199.61

Flat Glow Bar Igniter

This flat glow bar igniter is designed for gas ovens. The function of the part is to ignite the gas to light the oven burner. If your gas igniter does not glow, or if it glows but will not light, you may need to replace this part. The flat glow bar igniter is in the back of your gas oven. You will need to remove the access panel on the back of your oven to disconnect the igniter. Be sure that the gas source to the oven is shut off before you begin this repair. This part is sold individually.

$30.70

Door Hinge Receptacle

Sold individually.

$173.17

CLOCK/TIMER

$35.39

USE WCI 5303202116

$62.71

Door Handle - Black

Handle only.

$35.60

HINGE

$31.44

GASKET

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not heating to desired temperature

  • Customer: Dan from Bellevue, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 104 of 157 people found this instruction helpful
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with tw... read more

Inside glass just exploded when pre heating oven

  • Customer: George from Cleveland, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
I unscrewed 4 screws and took the door apart. The only trouble was I did not pay attention to the way the spacer was positioned. When I put the door back together I really had to look at the way it fit in the main part of the door. I had to use 2 small pieces of tape to hold the glass in place since the door was still atached to the oven and not laying flat.... read more

Clocktimer went out, why I don't know.

  • Customer: Rosemary from Glendale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Turned off power and gas. took off top brace held on with four small phillips screws.Then pulled face plate loose from front of Clock/timer. Then removed four large phillips screws holding the brace for the Clock/timer.Then removed the second set of four screws from each corner of the Clock/timer and disconnected the power wire attached to the clock/timer. P... read more