FFC07K1BW0 Frigidaire Freezer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door wasn't closing correctly.
My husband removed the old hinge, by taking out the old screws and the old hinge and attached the new one, by inserting the new hinge and the new screws. It was as easy as 123.
Parts Used:
-
Catrina from Calumet City, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge Broken
Took out the screws(8mm). Used pliers to close new hinges. Re-installed the screws with as large washers as would fit(to hopefully prevent the hinges from cracking at the screw holes like the originals did). I like this supplier, part was easy to find, correct part, shipped fast, price was good.
Parts Used:
-
David from Butler, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The freezer hinge was broke.
-
Shirleen from Olivet, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
5 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge broke
I used a socket set and removed old one and replaced with new one. Easy as 1 2 3. And I'm s 55 yr old female.
Parts Used:
-
Mary from OSTRANDER, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer would not start nor cool freeze
remove 2 screws from thermostat cover on side of freezer pulled temp nob off then removed temp control and copper temp sense rod by pulling out then unhook wires then reverse procedure to put back together
Parts Used:
-
ivan from MERLIN, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken hinge
Removed the bolts and broken hinge with lid closed. Installed new hinge. Removed the retaining nail from new hinge allowing it to have tension.
Parts Used:
-
Glen from BON AQUA, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke freezer lid hinge.
-
Dennis from COLORADO SPGS, CO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermostat would not hold the temperature
I replaced the thermostat. (Note: On a chest freezer, there is a copper tube going up into the wall of the freezer. The capillary of the thermostat goes into this tube.) 1. Unplug freezer. 2. Remove temperature knob. 3. Remove screws and remove cover plate. 4. Unclip old thermostat. 5. Using pliers, gently pull down the rubber seal on the capillary where it enters the copper tube. 6. Pull capillary out of copper tube. (In my case, the capillary was not free to pull out. I had to grasp the capillary with pliers and tug hard.) 7. Place rubber seal over the new capillary. 8. Insert the new capillary into the copper tube and put the rubber seal over the end of the copper tube. 9. Install thermostat body in the cover plate using the clip on the thermostat body. 10. Replace cover plate and temperature knob.
Parts Used:
-
Reynold from Belen, NM
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!