Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FEX831CS0 > Parts

FEX831CS0 Frigidaire Washer Dryer Combo - Parts

All parts for the Frigidaire Washer Dryer Combo FEX831CS0

Below is a list of all parts for the Frigidaire Washer Dryer Combo FEX831CS0. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the FEX831CS0
15-28 of 185
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$90.96

Heater Assembly

This dryer heating assembly has 5/16" terminal on the housing.

$9.28

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operating, you might need to replace the tension idler pulley. The tension idler pulley works in conjunction with the drive belt, so you might need to replace the belt as well as the pulley. Once the old pulley has been removed from the washer, you will need to transfer the spring and bushing from the old pulley to the new one before re-attaching it to the washer.

$8.61

Grounding Ball

This grounding ball is used in dryers and works to prevent friction in the rear bearing when the drum rotates. If your dryer is making a squealing, loud, banging noise or will not ...

$8.18

Door Strike

The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair that should only take a few minutes to complete. The package contains one strike. Open the dryer door, and use a flat head screw driver to snap the old strike out if it has not fallen out already. Simply push the gasket out of the way, squeeze together the strike and place inside of the opening. Wiggle to ensure it is set in place properly.

$31.36

Timer Knob

This knob accepts a D-shaped shaft.

$48.11

Tub Seal Assembly

If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace your old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.

$6.11

SCREW

$7.88

Grounding Ball Clip

This grounding ball clip is made of metal. Sold individually.

$30.38

Blower Wheel

$32.90

Idler Arm and Pulley

$6.36

SCREW

Sold individually.

$28.49

Terminal Block Kit

This kit includes 3 screws and 3 terminals.

$71.04

Water Valve - 115V

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$41.91

Drain Hose

This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before placing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.

All Parts for the FEX831CS0
15-28 of 185