Models > FES330KQ1 > Instructions

FES330KQ1 Roper Range - Instructions

All installation instructions for FES330KQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FES330KQ1
46-60 of 137
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Rear Drawer Glide

  • Customer: Ed from Maple Grove MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

Eroding burner drip bowls

  • Customer: Edward from Hamilton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement

Drip bowls were rusty and rotting through

  • Customer: Michael from Kings Park NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better!

back burner would not heat

  • Customer: wayne from whittemore IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
removed the heating element then removed the screw that holds the plug in on cut the two wires and reconnect the two wires and put back

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 11 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Receptacle Assembly has burned out

  • Customer: ANN from MANITOWOC WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Remove old receptacle and connected and replace new one. Burner now works perfectly again.

Ugly looking drip bowl.

  • Customer: Irina from Green Cove Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

replacement of drip bowll

  • Customer: Gudrun from Santa Fe NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
take the old one out, but the new one in.

the screws fell out of sides and bottom of door,bottom frame was bowed out.

  • Customer: Christine from Clinton Twp. MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I had to get someone to help he thought we ordered wrong parts. called part select and was told to call whirpool direct. found out the part was redesigned unkown to us. So we were trying to fit parts that didn't need screws and now I have extra screws that I will send back.

door glide broken

  • Customer: David from Port Orange FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed the old ones.then installed the new ones.

range handle fell off and screw got lost

  • Customer: Frances from palm beach gardens FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

burnt out drip pans

  • Customer: Barbara from KAMUELA AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

My drip bowls were scorched and discolored and difficult to clean

  • Customer: Claudia from Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

the drip bowls had rusted through

  • Customer: DANIEL from sanborn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.

slides on lower drawer were broken

  • Customer: Leona R from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.
All Instructions for the FES330KQ1
46-60 of 137