Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FES330EQ0

FES330EQ0 Roper Range - Overview

Get Parts and Repair Help for FES330EQ0

If you know the range repair part you need, you can browse the list of all parts on the FES330EQ0, or you can search by name or part description. You can also find your part by where it is located on the FES330EQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for FES330EQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.17

Chrome Drip Bowl - 8"

This drip bowl is also known as a drip pan, and it is designed for use with cooktops and ranges. It sits below 8-inch burner elements, and catches drips and spills from the cookwar...

$9.44

Drip Bowl - 6"

If your element will not heat, there could be an issue with your drip bowl. This 6 inch chrome drip bowl fits most electric ranges. Before you replace the drip bowl, make sure the element is turned off and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and replace the element. Make sure the small hole on the bowl lines up with the element socket. The manufacturer has substituted this part, it has a hole in the center, and no longer has a solid bottom. For a step by step guide, click the video below.

$46.38

Bake Element

This bake element is located at the bottom of the oven to supply heat and it has push-on terminals. If your baking element is burnt out, the heat is not consistent, or is defective...

$3.02

Screw

This screw is sold individually.

$19.63

Receptacle Kit

This assembly of parts is a surface burner receptacle kit, and is used in conjunction with your range. The assembly comes with two wires, two wire nuts, two pieces of heat-shrink t...

$30.57

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inches in length, and comes with 2 ceramic wire nuts. Fault temperature sensors are often responsible for F3 and F4 error messages on an electric range. Furthermore, if you find your oven is too hot, will not heat evenly, or simply will not heat at all, there could be an issue with your temperature sensor and you should look to replace it immediately.

$7.36

Rear Drawer Glide

This OEM replacement rear drawer glide supports the storage drawer on your range, and allows the drawer to open and close with ease. If your storage drawer will not open or close, ...

$45.09

Oven Rack

This oven rack is a piece for your range. The oven rack is sold individually and is silver in color. The function of this part is to provide a balanced and flat surface for your cookware to sit inside your oven. The measurements of this piece are 24 inches wide and 16 inches deep. When replacing your old oven rack with your new piece, no tools are required. Before making this installation, make sure your range is turned off and your oven has cooled down inside.

$3.02

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an ...

$49.85

Surface Burner Element - 8"

This plug-in surface burner element has looped terminal ends.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls were rusty and rotting through

  • Customer: Michael from Kings Park, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 480 of 482 people found this instruction helpful
I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better! read more

Just Replaced Ole Drip Bowls.

  • Customer: Roger from Osage Beach, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 377 of 383 people found this instruction helpful
Unplugged burners. . . . . Removed old bowls and replaced with new. . . . . . Plugged burners back in. However, I do want you to know that I could not believe the promptness of your service and the courteous customer service person that assisted me with my problem in selecting the correct drip bowls. You are definitely a unique company!!!! read more

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 140 of 179 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more