Models > FES310BW1 > Instructions

FES310BW1 Roper Range - Instructions

All installation instructions for FES310BW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FES310BW1
46-60 of 315
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bake Element went bad, will not work.

  • Customer: Kent from Spooner WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

burner fell apart

  • Customer: Barbara a from Huntington NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Plugged in the new burner, which we received in one day.We were delighted with the quick service

Burners weren't heating

  • Customer: james from killingworth CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

burner inop

  • Customer: Donald from Milford MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

COOKTOP ELEMENTS WORKED INTERMITTANTLY.

  • Customer: CHARLES from SOMERSWORTH NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
TURN THE POWER OFF TO THE UNIT. REMOVE THE COLD ELEMENT BY LIFTING UP AND PULLING OUT. REMOVE THE DRIP PAN. REMOVE THE ELEMENT PLUG SCREW AND PULL THE PLUG UP AND OUT OF THE SOCKET. CUT THE LEADS TO THE PLUG AS CLOSE TO THE PLUG END AS POSSIBLE TO ALLOW ENOUGH WIRE TO SPLICE THE NEW PLUG IN. STRIP THE INSULLATION BACK 3/8" TO ALLOW FOR SPLICING. INSTALL THE SHRINK TUBE COLLAR ON THE WIRE AND PLACE ONE NEW LEAD (PRESTRIPPED AT THE FACTORY)NEXT TO THE OLD WIRE AND PLACE THE WIRE NUT PROVIDED OVER THE BARE WIRE ENDS AND TWIST IT ON UNTIL IT IS TIGHT. BEND THE WIRE NUT SPLICE BACK OVER ONE OF THE LEADS AND SLIDE THE SHRINK TAPE OVER IT. HEAT UP THE SHRINK TAPE WITH A HAIR DRYER TO MAKE IT TIGHT OVER THE WIRE NUT CONNECTION. REPEAT THE PROCESS FOR THE NEXT LEAD. SLIDE THE LEADS INTO THE NEW SOCKET. INSTALL THE SOCKET AND SECURE THE THE NEW SCREW PROVIDED. REINSTALL THE DRIP PAN AND PLUG IN THE HEAT ELEMENT. FOLLOW THE SAME PROCEDURE FOR EACH ELEMENT SOCKET REPLACED. TURN THE POWER BACK ON.

Bake Element Failed

  • Customer: Johnson from Norwood CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.

Broiler unit would not heat

  • Customer: Robert from Atlanta GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

Store-bought drip bowls wouldn't fit.

  • Customer: Sharon from Yacolt WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.

  • Customer: Christopher from Arlington NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!

items in the oven were not baking properly. We discovered the bake elemnent wasn't working and looked defective in one part.

  • Customer: Douglas from Raymond NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.

The original knob had broken off

  • Customer: Yvonne from Warminster PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Just placed the knob over where the old one sat and it worked fine. Thank you.

Broiler wouldn't heat

  • Customer: Diane from Mill Valley CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

old heating element "popped"

  • Customer: Sally from Chesterfield MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!

Oven wouldn't heat

  • Customer: Don from Rutland VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires fom the old element .. connected them to the new element ... put the screws back ...and tested. problem solved

The upper broiler element had burnt and broken into.

  • Customer: William from Manteno IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 2 of 4 people found this instruction helpful
I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.
All Instructions for the FES310BW1
46-60 of 315