Models > FES310BW1 > Instructions

FES310BW1 Roper Range - Instructions

All installation instructions for FES310BW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FES310BW1
31-45 of 332
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Both heating elements would not work.

  • Customer: Lee from Austin TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
After shutting off the power, I removed the door and oven racks. Then, by using a screwdriver, I removed each element one at a time and replaced with the new element. Each element pulled away from the back wall and was connected electrically by Sta-Kon connectors. All went well, and the unit was operational in about 30 minutes. I still have to remove the oven from the wall to replaced the two door springs.

BROIL ELEMENT WAS BURNED OUT

  • Customer: DAVID from COTTAGE GROVE WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 11 people found this instruction helpful
1. MOVE OVEN OUT FROM WALL
2. REMOVE BACK PANEL OF OVEN, 8 SCREWS
3. REMOVE 3 SCREWS INSIDE OVEN HOLDING ELEMENT
4. PULLED WIRE CONNECTIONS OFF OF ELEMENT
5. REVERSE PROCEDURE TO INSTALL NEW ELEMENT

Loose terminal caused block to overheat and break

  • Customer: Dana from Black Mountain NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

THE BOTTOM ELEMENT WAS NOT HEATING

  • Customer: y.d. from lagrange KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
UNPLUG FIRST THEN TOOK BACK OFF AND TOOK WIRE CLIPS OFF AND CONNECTECTED THE OTHER ON IN WORKED FINE YOU WILL LIKE PART SELECT I JUST ORDERED APART FOR MY FRIG. WAITING FOR IT NOW.

Sparks emitted at burner connection and burner does not work.

  • Customer: Doug from Puyallup WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

Original burners were not working correctly.

  • Customer: Sharon from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
I received my ordered in less than a week. It was great. The day I got them I remove the old burners and replaced them with the new ones. It took me about 3 minutes total. I was then able to cook my Christmas dinner with out any problems.

burned out element

  • Customer: Lee from Laceys Spring AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

The drip bowls were all caked and corroded.

  • Customer: Terry from Mountain City TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

electric coils would not stay flat as drip pans were incorrect fit

  • Customer: Janet from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
replaced drip pans with correct type

Electric burners where consistently intermittently working right. Sometimes they would work on High but not able to adjust to low heat. Sometimes they would just not want to come on at all. Occasionally there was a spark at the connection. If I jiggled the element just right it may or may not wo

  • Customer: JOAN from Pickford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Thought we was going to have to replace the range all together, due to most parts not being available for this model anymore. Since this is an expensive model, we did not look forward to having to replace it. So I thought just by chance I would check to see if anyone had parts to help in repairing it. Part Select did happen to have the Surface Plug-in block kit that was needed. After going at least a year with this problem, I am sooooo happy to say it is finally fixed and working great! Thanks much Parts Select.

oven unit burned up.

  • Customer: Jerry from Mt. Gilead OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.

burner fell apart

  • Customer: Barbara a from Huntington NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Plugged in the new burner, which we received in one day.We were delighted with the quick service

Sparking Burner

  • Customer: Patti from Burbana IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
Followed instructions from previous repair story!!
Pulled old burner out. Unscrewed plug element. Cut old wires back about 6 inches from plug. Attached new part with wire nuts provided and covered with shrink sleeves provided. Attached plug with provided screw and slipped in new element. Works great!!
I want to thank the previous posters for posting their detailed repair stories....without reading those, I may have called a repair service and paid big bucks. Thanks to all previous posters for the detailed information they provided!! PS...The parts arrived in amazingly quick!!

replacing the hold down clip for the burner

  • Customer: Roseanne from North Syracuse NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
Started out removing the old clip that didnt hold burner element down anymore. It was a bit rough, since i was taking off a rivet. I used the screwdriver to carefully wedge the edges of the rivet upward so that i could get the wire cutters underneath it enough to snap the head off. After some fanagling for about 20 minutes, i popped it off. The rest of the repair went like cake, and i am soooo thankful that the replacement part i ordered from you included a screw and a nut. Next time, if there is a next time, this repair could be done in 2 minutes. THANK YOU FOR SAVING THANKSGIVING AND A $100 REPAIRMAN SERVICE COST FOR A $10 PART!!!

COOKTOP ELEMENTS WORKED INTERMITTANTLY.

  • Customer: CHARLES from SOMERSWORTH NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
TURN THE POWER OFF TO THE UNIT. REMOVE THE COLD ELEMENT BY LIFTING UP AND PULLING OUT. REMOVE THE DRIP PAN. REMOVE THE ELEMENT PLUG SCREW AND PULL THE PLUG UP AND OUT OF THE SOCKET. CUT THE LEADS TO THE PLUG AS CLOSE TO THE PLUG END AS POSSIBLE TO ALLOW ENOUGH WIRE TO SPLICE THE NEW PLUG IN. STRIP THE INSULLATION BACK 3/8" TO ALLOW FOR SPLICING. INSTALL THE SHRINK TUBE COLLAR ON THE WIRE AND PLACE ONE NEW LEAD (PRESTRIPPED AT THE FACTORY)NEXT TO THE OLD WIRE AND PLACE THE WIRE NUT PROVIDED OVER THE BARE WIRE ENDS AND TWIST IT ON UNTIL IT IS TIGHT. BEND THE WIRE NUT SPLICE BACK OVER ONE OF THE LEADS AND SLIDE THE SHRINK TAPE OVER IT. HEAT UP THE SHRINK TAPE WITH A HAIR DRYER TO MAKE IT TIGHT OVER THE WIRE NUT CONNECTION. REPEAT THE PROCESS FOR THE NEXT LEAD. SLIDE THE LEADS INTO THE NEW SOCKET. INSTALL THE SOCKET AND SECURE THE THE NEW SCREW PROVIDED. REINSTALL THE DRIP PAN AND PLUG IN THE HEAT ELEMENT. FOLLOW THE SAME PROCEDURE FOR EACH ELEMENT SOCKET REPLACED. TURN THE POWER BACK ON.
All Instructions for the FES310BW1
31-45 of 332