Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FER641FS0

FER641FS0 Frigidaire Dryer - Overview

Get Parts and Repair Help for FER641FS0

If you know the dryer repair part you need, you can browse the list of all parts on the FER641FS0, or you can search by name or part description. You can also find your part by where it is located on the FER641FS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for FER641FS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.91

Rear Drum Bearing Kit

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...

$8.17

Drum Belt

This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving that is a sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 87 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin repair work.

$7.59

Selector Knob

This selector knob may also be known as the laundry appliance control knob and is meant for your washer or dryer. This model is sold individually and takes a D-shaped shaft. The pu...

$20.80

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear b...

$72.98

Heating Element Assembly

This dryer heating element produces heat to dry clothes and is located in the rear of a dryer. If the heater element is burned, the dryer does not heat or over heats, or clothes are taking too long to dry, replacing this part could solve your problem. The tools needed for this repair project are a Phillips screwdriver, putty knife, and needle nose pliers. To repair, first remove the main top of the dryer and ground strap at the rear. Disconnect the two wire harnesses and remove the screws that hold the front panel to the cabinet, in order to pull out the front panel. Now that you have access to the inside of the dryer, refer to the manual for further installation instructions and detailed guidance. Remember to unplug your appliance from the power source before beginning this repair project.

$9.38

Thermal Limiter - Limit 220

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenhe...

$13.16

Lower Front Felt Seal with Adhesive

$28.01

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$11.67

Lint Filter

Located at the front of the dryer, this lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 12 inches long x 7 inches high, has a plastic frame, and a mesh body to catch debris. If your filter needs cleaning, the dryer cycle will take longer due to a buildup of lint or fabric softener affecting the air flow through the filter. If there is a buildup, try scrubbing the filter with hot water and soap. If the filter is damaged or torn, it should be replaced. Cleaning the lint filter before starting the drying cycle is a great way to ensure your dryer performs properly.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer squealed like a pig and at times the drum stopped rotating

  • Customer: charles from new holland, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 637 of 648 people found this instruction helpful
First thought the problem was a stretched drum belt or bad idler pulley. Ordered a new belt and idler assy plus spring. Replaced those items with relative ease following suggestions obtained at this site.However, problem persisted and I now suspected a bad drum bearing. Odered the bearing kit and replaced same using the following procedure.
1. Removed ... read more

Knob replacement

  • Customer: Kevin from Donalsonville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 377 of 384 people found this instruction helpful
Just slipped them on and ready to go. Ordered them on thur and got em on Tues. read more

Loud Squeaking

  • Customer: Frank from Boyertown, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 293 of 301 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more