Models > FEP310KW1 > Instructions

FEP310KW1 Roper Range - Instructions

All installation instructions for FEP310KW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310KW1
1-15 of 110
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Just replaced ole drip bowls.

  • Customer: Roger from Osage Beach MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 364 of 368 people found this instruction helpful
Unplugged burners.....removed old bowls and replaced with new......plugged burners back in.

However, I do want you to know that I could not believe the promptness of your service and the courteous Customer Service person that assisted me with my problem in selecting the correct drip bowls. You are definitely a unique company!!!!

The drip bowls on my elderly mother's electric range needed to be replaced.

  • Customer: Frank from Derwood MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 80 of 145 people found this instruction helpful
Replacing the bowls was simple, simply removing the burner units and pulling out the bowls and inserting the new ones.

The ONLY reason I am answering this questionaire is to complement Partselect.com for their incredibly fast shipping of my parts after I placed the order. I received my order within 2-3 days with normal shipping. I expected to wait at least a week or longer. Thanks again Partselect.com for being there when I needed you the most!

Drip bowls was extremely dirty and burnt

  • Customer: Dr. Robbin from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 69 of 132 people found this instruction helpful
So often we feel inclined to contact repairmen for simple jobs. This was easy because I ordered the part by looking on the side of the range. It arrived in less than a week. I simply snap the bowls inside the correct sockets and now my stove looks new. I definitely would use this service again.

Stove would not heat up

  • Customer: Tim from Pittsford NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 29 of 36 people found this instruction helpful
Cut old wires to receptacle, striped the wires, wire nutted to new receptacle, screwed new receptacle into stove and installed heating element.

Piece of cake, but then again my degree is in electrical engineering so I should be able to handle a couple of wire nuts.

heating element burnt up

  • Customer: Esther from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 25 of 27 people found this instruction helpful
first I pulled the stove from the wall. Then unplugged the stove from the wall (electric stove) for safety. then I removed the middle back panel screws(2) and then the panel. I then pulled the wires off the heating element that was bad. I took the screws (2) off the heating element inside the oven. I had to use WD-40 to loosen the screws because with the heat they were really stuck. I removed the heating element and replaced it with the one I got through partselect.com. Put everything back and walla finished. Partselect.com sent me the right part at the right price and fast. No hassles at all.

The burner would keep heating after turning off the switch

  • Customer: RON from KAUFMAN TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 22 of 24 people found this instruction helpful
Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes

mice had made nests in the insulation wrap in the range

  • Customer: Wendy from Red Hook NY
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 14 of 14 people found this instruction helpful
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

The old switch broke off.

  • Customer: Bruce from Pasadena MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 21 people found this instruction helpful
Removed two screws that held the unit in then pulled out a few inches so I could see where the 5 wires were. Then I replaced one at a time till done. then replaced the retaining screws.

Lower element went out

  • Customer: Kimberly from Palestine TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

someone did not install cord properly! they left a strong strain on one of the 3 wires, with a loose nut connection that caused it to heat and melt the plastic that poped out toward the rear metal cover and short circuited.

  • Customer: Richard from Daytona Beach AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 13 people found this instruction helpful
I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

drawer broke and annoying my wife

  • Customer: John from Jamestown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
screwed in the new glide by taking out old broken one and screwing in new one. wife happy now.

Burner was not heating up

  • Customer: Gary from Hellertown PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 18 people found this instruction helpful
Puled out the electical plug . Removed the back panel. Pulled off the switch knob. Removed the 2 screws holding the switch. Took the wires off of the old switch and placed them on the corespondig connector on the new switch. Put everything back in reverse order.

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

bought floor model with loose cord that melted block terminal

  • Customer: larry from alexandria IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 7 of 8 people found this instruction helpful
Safety first always shut breaker off at box.
I unplugged stove, disconnected wires keeping in mind the color placement. Unscrewed one ground screw and removed terminal block. Attached new block with ground screw, replaced wires in correct order, re-attached plug. Then reattached safety cover. Pretty simple for d.i.y.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
All Instructions for the FEP310KW1
1-15 of 110