Models > FEP310KW0 > Instructions

FEP310KW0 Roper Range - Instructions

All installation instructions for FEP310KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310KW0
46-60 of 123
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burner plug broken

  • Customer: Norman from Newport NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.

Bad Receptacle

  • Customer: TROY from YPSILANTI MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!

Block broke

  • Customer: Edward from Crimora VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Receptacle Assembly has burned out

  • Customer: ANN from MANITOWOC WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Remove old receptacle and connected and replace new one. Burner now works perfectly again.

Ugly looking drip bowl.

  • Customer: Irina from Green Cove Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

burnt out drip pans

  • Customer: Barbara from KAMUELA AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

replacement of drip bowll

  • Customer: Gudrun from Santa Fe NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
take the old one out, but the new one in.

the drip bowls had rusted through

  • Customer: DANIEL from sanborn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.

door glide broken

  • Customer: David from Port Orange FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed the old ones.then installed the new ones.

slides on lower drawer were broken

  • Customer: Leona R from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

the screws fell out of sides and bottom of door,bottom frame was bowed out.

  • Customer: Christine from Clinton Twp. MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I had to get someone to help he thought we ordered wrong parts. called part select and was told to call whirpool direct. found out the part was redesigned unkown to us. So we were trying to fit parts that didn't need screws and now I have extra screws that I will send back.

Old Drip Bowls

  • Customer: James from Edgewater MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Lifted out the old ones and inserted the new ones and my range top looks brand new now!

none

  • Customer: Dennis from Viroqua WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled out the burners, cleaned up the crumbled drip pans ,installed the new drip pans, pluged in the burners and was finished in about 3 minutes. I will order again from you. Thank you.

my drip bowls were old an I was unable to clean them

  • Customer: Anne Marie from Albany NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the old drip pans out and replace them with the new ones. Now my stove looks brand new. These were a perfect fit.

arcing within the cook top electric heat element and the receptacle.

  • Customer: Paul from Levittown NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Cut, splice and heat shrink.
All Instructions for the FEP310KW0
46-60 of 123