Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FEP310KW0 > Instructions

FEP310KW0 Roper Range - Instructions

All installation instructions for FEP310KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310KW0
31-45 of 123
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven heating irradically.

  • Customer: Ruth from Oregon, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
This did not solve the problem. Since we were still under warranty we called the store where we bought the appliance and they are sending a repairman next week. We even ordered a sensor and installed that too but that didn't help.

Must be in the circuit board or something. We'll see. Thanks anyway

I snapped a bolt on the main power terminal block when connecting the pigtail.

  • Customer: Frank from Palm Coast, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 6 people found this instruction helpful
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

The heating coil was no longer working.

  • Customer: Amanda from Midwest City, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Broken Rear Drawer Glide

  • Customer: Ed from Maple Grove, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

thermostat knob tore off

  • Customer: SHARON from FRUITLAND PARK, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
my boyfriend took part of the back off unscrewed a few screws took the old one out and put the new one in. It seemed simple to me I was surprised. I knew the cost would have been more than double the part if I had called an appliance technician to do it. I received the part the next day which I was tatally suprised since it was a Saturday. I am very satisfied with Parts Select inventory and service Thank You

baking element non operational

  • Customer: GARY from JACKSON, WY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

Receptacle Assembly Has Burned Out

  • Customer: ANN from MANITOWOC, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
Remove old receptacle and connected and replace new one. Burner now works perfectly again.

Oven selector switch hit by lightning-dead short

  • Customer: Eric from Cascade, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 10 people found this instruction helpful
Removed rear access panel (after disconnecting plug). Removed 2 screws holding switch and attached all wires to the new switch and installed. The pictures on the website helped a lot. It's hard to order the wrong part with the information you supply. Part was delivered promptly. Overall this was a good experience. I will buy from you again.

burnt out drip pans

  • Customer: Barbara from KAMUELA, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

My drip bowls were scorched and discolored and difficult to clean

  • Customer: Claudia from Milwaukee, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Broken rear stove drawer glide

  • Customer: John from Maysville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

It was a rather simple fix--just replacing burner pans

  • Customer: Vicki from Jefferson, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

burner plug broken

  • Customer: Norman from Newport, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.

back burner would not heat

  • Customer: wayne from whittemore, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
removed the heating element then removed the screw that holds the plug in on cut the two wires and reconnect the two wires and put back

element went out on the stove

  • Customer: christopher from harrisburg, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's
All Instructions for the FEP310KW0
31-45 of 123