Models > FEP310KW0 > Instructions

FEP310KW0 Roper Range - Instructions

All installation instructions for FEP310KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310KW0
16-30 of 104
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no oven or broiler both went out at same time

  • Customer: Thomas from Ney OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
turn the power off remove the back cover 7- sheet metal screws then removed the 2-screws to the switch pulled it out enough to swittch the wires and ran the copper temp sensor in the oven mounted the switch

Heating element burned up

  • Customer: Jerry D from Spring Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

Broken Switch

  • Customer: Richard from Mariposa CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 17 people found this instruction helpful
Made sure was off, Removed rear panel, removed 2 screws, removed wire clips from old switch, installed wires on new switch, installed switch with 2 screws, re-installed back panel, reconnected power and checked switch function. OK!

Heating element bent, drip bowl corroded

  • Customer: Jason from Fayetteville AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I just put the drip bowl in and plugged in the new heating element and I was done. It heats much faster and is level now so cooking is much easier. Also the parts arrived sooner than I expected, so I was very satisfied overall. Couldn't have been much easier all around. I will use Partselect.com in the future. Thanks

Stove burner wouldn't heat

  • Customer: DAICHI from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 10 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

Loose terminal caused block to overheat and break

  • Customer: Dana from Black Mountain NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

broken bottom drawer glide and missing rivet on drawer front panel

  • Customer: David from Fairborn OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

I snapped a bolt on the main power terminal block when connecting the pigtail.

  • Customer: Frank from Palm Coast FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Bottom drawer

  • Customer: Eric from Saint Michael MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

Oven heating irradically.

  • Customer: Ruth from Oregon IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
This did not solve the problem. Since we were still under warranty we called the store where we bought the appliance and they are sending a repairman next week. We even ordered a sensor and installed that too but that didn't help.

Must be in the circuit board or something. We'll see. Thanks anyway

Broken Rear Drawer Glide

  • Customer: Ed from Maple Grove MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

Broken drawer glides

  • Customer: Shane from Palatine IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.

Oven selector switch hit by lightning-dead short

  • Customer: Eric from Cascade VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
Removed rear access panel (after disconnecting plug). Removed 2 screws holding switch and attached all wires to the new switch and installed. The pictures on the website helped a lot. It's hard to order the wrong part with the information you supply. Part was delivered promptly. Overall this was a good experience. I will buy from you again.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 16 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
All Instructions for the FEP310KW0
16-30 of 104