Models > FEP310BW1 > Instructions

FEP310BW1 Roper Range - Instructions

All installation instructions for FEP310BW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310BW1
76-90 of 333
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Stove-top Burner intermittently shut off and on-wouldn't heat properly

  • Customer: George from New Bloomfield PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.

  • Customer: Lowell from Aberdeen MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley

burnt out bake element

  • Customer: richard from burnthills NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.

Bake Element quit working

  • Customer: denise from swartz creek MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.

bottom element burnt out

  • Customer: brenda from las vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
removed 2 screws . pulled out the 2 wires and disconect them. took out the element. Put the new element in and hooked the wires up. placed the metal bracket to the back and put in the 2 screw and turned it on and it worked like new.
Brenda

Burner would not heat up.

  • Customer: Nancy from Baldwinsville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Bottom element was burned out

  • Customer: Veronica from Brunswick GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.

replaced two baffles

  • Customer: Glenn from Bonham TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
took off the dryer by remving two screws, then the front panel. Then removed the screws that held in the drum, pulled the drum out replaced the baffles then put it back together. It was easyer then I thought. It took less them 30 mins.

DEAD SHORT IN BAKING ELEMENT

  • Customer: JIMMY from GRAY TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
DISCONNECT POWER TO THE OVEN AT CIRCUIT BREAKER.MOST IMPORTANT CONFIRED POWER REMOVED BY TURNING ON BUNER,ALSO WITH ELECTRIAL METER.REMOVE HEX SCREW. PULLED PURNER FORWARD APPROX 3 INCHES REMOVE THE TWO WIRES TO BURNER ELEMENT .INSTALLED NEW BURNER REVERSE ROTATION .RETURNED POWER TO OVEN,ALL WAS WELL NO PROBLEMS.NOT TO SURE OF BURNER WATTAGE ON OLD AND NEW UNIT,AS TWO BURNERS ARE AVAIABLE FOR THIS UNIT.ALL OK .THANKS TO PARTS SELECT FOR SPEEDY PART NEEDED

2 of the burners were not working arching and smoking

  • Customer: Tina from Laurel MT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

Three of four electric coils won't turn on

  • Customer: Arsenio from Beaverton OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

My drip pans were in bad shape

  • Customer: Sandra from Oldsmar FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed

Element went bad

  • Customer: Philip from Coral Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

THE PROBLEM WAS THAT THE PLUG WAS GONE IT FELL DOWN OUT OF THE BRACKET

  • Customer: Elnora from Brundidge AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I TOOK THE OLD WIRES AND PLUG OFF AND REPLACED IT WITH THE NEW BLOCK IT WORKS FINE

Oven got warm - Temp light stayed lit.

  • Customer: CHRISTOPHER from VALATIE NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested
All Instructions for the FEP310BW1
76-90 of 333