Models > FEP310BW1 > Instructions

FEP310BW1 Roper Range - Instructions

All installation instructions for FEP310BW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310BW1
46-60 of 333
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Electric stove burners working intermitantly.

  • Customer: Michael from St. Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).

Broiler unit would not heat

  • Customer: Robert from Atlanta GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

burner fell apart

  • Customer: Barbara a from Huntington NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Plugged in the new burner, which we received in one day.We were delighted with the quick service

Bake Element went bad, will not work.

  • Customer: Kent from Spooner WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

COOKTOP ELEMENTS WORKED INTERMITTANTLY.

  • Customer: CHARLES from SOMERSWORTH NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
TURN THE POWER OFF TO THE UNIT. REMOVE THE COLD ELEMENT BY LIFTING UP AND PULLING OUT. REMOVE THE DRIP PAN. REMOVE THE ELEMENT PLUG SCREW AND PULL THE PLUG UP AND OUT OF THE SOCKET. CUT THE LEADS TO THE PLUG AS CLOSE TO THE PLUG END AS POSSIBLE TO ALLOW ENOUGH WIRE TO SPLICE THE NEW PLUG IN. STRIP THE INSULLATION BACK 3/8" TO ALLOW FOR SPLICING. INSTALL THE SHRINK TUBE COLLAR ON THE WIRE AND PLACE ONE NEW LEAD (PRESTRIPPED AT THE FACTORY)NEXT TO THE OLD WIRE AND PLACE THE WIRE NUT PROVIDED OVER THE BARE WIRE ENDS AND TWIST IT ON UNTIL IT IS TIGHT. BEND THE WIRE NUT SPLICE BACK OVER ONE OF THE LEADS AND SLIDE THE SHRINK TAPE OVER IT. HEAT UP THE SHRINK TAPE WITH A HAIR DRYER TO MAKE IT TIGHT OVER THE WIRE NUT CONNECTION. REPEAT THE PROCESS FOR THE NEXT LEAD. SLIDE THE LEADS INTO THE NEW SOCKET. INSTALL THE SOCKET AND SECURE THE THE NEW SCREW PROVIDED. REINSTALL THE DRIP PAN AND PLUG IN THE HEAT ELEMENT. FOLLOW THE SAME PROCEDURE FOR EACH ELEMENT SOCKET REPLACED. TURN THE POWER BACK ON.

Store-bought drip bowls wouldn't fit.

  • Customer: Sharon from Yacolt WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Bake Element Failed

  • Customer: Johnson from Norwood CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.

burner inop

  • Customer: Donald from Milford MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

Burners weren't heating

  • Customer: james from killingworth CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

replacing the hold down clip for the burner

  • Customer: Roseanne from North Syracuse NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
Started out removing the old clip that didnt hold burner element down anymore. It was a bit rough, since i was taking off a rivet. I used the screwdriver to carefully wedge the edges of the rivet upward so that i could get the wire cutters underneath it enough to snap the head off. After some fanagling for about 20 minutes, i popped it off. The rest of the repair went like cake, and i am soooo thankful that the replacement part i ordered from you included a screw and a nut. Next time, if there is a next time, this repair could be done in 2 minutes. THANK YOU FOR SAVING THANKSGIVING AND A $100 REPAIRMAN SERVICE COST FOR A $10 PART!!!

Element broke into several pieces

  • Customer: Gary from Longview TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Was able to use a philips screwdriver and remove 2 screws. I then clean the bottom of the oven. The installation was even easier. Took less than 5 minutes. Saved over $60.00 in labor cost

The bottom element of the oven stopped working, therefore, we could not bake anything.

  • Customer: STEPHEN from SEMORA NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First, I turned the breaker off to the oven, that's the most important step.
Next, I turned on the oven to make sure the oven was not energized.
I then took out two phillips screws that were holding the baking element in place.
Next I pulled the element out slowly to expose the wires that connected to the element.
I removed the connecters, took out the damaged element, replaced it with the new element.
Last, I screwed the two phillips screws back in, and saved a $65.00 service call.

Broiler wouldn't heat

  • Customer: Diane from Mill Valley CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

old heating element "popped"

  • Customer: Sally from Chesterfield MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!

Intermittant heating, arcing in the socket

  • Customer: David from Jefferson Hills PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Simple to do. Remove old element, remove screw holding socket, cut the socket wires with 2 inches to spare, assemble the newsocket and wires with heat shrink tubing, strip range wires, apply the wire nuts as instructed and shrink the tubning with a heat gun.

Screw on the socket to the range. Shut the lid and install the element.

The replacemnet screw is thicker than the original one, so you might want to drill out the hole very slightly. I did not but the resistance was high on getting the screw fully seated.

Works great
All Instructions for the FEP310BW1
46-60 of 333