Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FEP310BW1 > Instructions

FEP310BW1 Roper Range - Instructions

All installation instructions for FEP310BW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310BW1
316-330 of 335
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower oven element not heating

  • Customer: Richard W from Pueblo, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the door and racks to get easy access to the electrical connection. I loosened the screws holding the element in place and disconnected the element from the electrical connection. I connected the new element and inserted the screws firmly attaching it in place. I placed the racks in the desired location and then put the door back on the hinges.

Burners did not get hot or went on and off

  • Customer: Boyd from kalamazoo, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

The bottom heating element burned out.

  • Customer: Ferdinand from Bent Mountain, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off the circuit breaker for the oven. 2. Verify that the power is OFF and all baking controls are OFF. 3. Remove all racks from the oven. 4. Remove the 2 screws with a #2 crosshead screwdriver. 5. Gently pull the element out. 6. Pull the spade lug terminals carefully off the element and take the old element out. 7. Put in the new element by attaching the spade lug terminals. 8. Line up the holes and reattach the element to the oven wall with the 2 screws. 9. Verify that all baking controls are off. 10. Turn on the circuit breaker for the oven. 11. Turn on the oven controls and verify that the new element is working. 12. Turn OFF the baking controls and reinstall the racks.

The element just broke in pcs.

  • Customer: Gordon from Northwood, ND
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off power,take out 2 screws to release element, unplug wires, pull out old element, put new element in hook up wires, put in 2 screws, and walla all done. Turn power back on. One thing to do that I did not. Clean the tag off before starting element. I got smoke from that.

upon disconnect, the wire leads sprung back inside their outlet holes

  • Customer: William from Demopolis, AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws holding element in place. Removed wire leads from element. Wire leads were under a bit of tension which pulled them back through their holes in rear oven wall. This required taking back of oven off to reinsert wires through holes. Used a clip to hold wires and prevent them from going back through holes. Attached wires to new element and removed clips. Placed element bracket in place and discovered that both screws had stripped threads (due to years of vibration, I'm guessing). Rummaged through garage and found two screws that worked. Replaced back of oven and re-plugged oven into outlet.

Bake element in oven broke (snapped in one place)

  • Customer: Linda from Prescott, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TURNED OFF POWER to oven! Removed the oven racks to make work room. I unscrewed the two phillips head screws holding the element in place. Pulled the element out to expose the wiring clipped to the element. Pulled the wiring clips off the old element, clipped them onto the new element. Pushed the whole thing back into place in the back wall of the oven. Turned on power and checked to make sure everything was working. Screwed the two screws back in place. Baked a sweet potato and took a picture!

oven heating element burned out.

  • Customer: Holly from Port Townsend, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removal easy, re-inserting the new element difficult because receptacle, "lost in insulation". Had to probe around with fishing scissors to locate and install. Heating element sent was bent out of shape. Not sure it will heat oven evenly for baked goods. Since the oven was in such bad shape and was so old, I am not placing much hope that it will last long, thus am not that concerned about even heating when its days are numbered.

Two Screws Holding The Bake Element Frozen Due To Age

  • Customer: Robert from Gastonia, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Used bic lighter to heat the screwsn and was easy to remove, no damage

Burner failure

  • Customer: Robert from Brookfield, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed and replaced burner unit.

burner fell apart

  • Customer: judy from coarsegold, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just plugged it in and away I went.

Broiler Unit Not working!

  • Customer: Joyce I from IRVING, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I oedered a new unit matched with the Model Number! Installed .It did not work.They said Part amybe defectice.They quickly sent out another.That was installed and did not work.I contacted them again and they sugessted the Modular unit that regulated the Heat Temp. They were discontinued. They suggested I contact Corecentic Solution.com which I did.I am now in the process of shipping out my Modular Element to have it rebuilt. My stove is over 20 Yrs old .It inly costs me $110.00 to fix ourselves. Thank YouParts Select.com. You saved me over $1700.00 It would have cost to buy a new stove. They also gave me a full refund on the two units they shipped out. They are a wonderful helpful Company and will take care of your parts needs. Thanks Again Joyce

Bake element stopped working

  • Customer: Jan from Plano, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off breaker to oven. Unscrewed the screws, disconnected the wires and removed the old element. Reversed the procedure to install the new part. Flipped on the breaker, turned on the oven and presto....the new element lit up! Appreciated your quick service. I will used Part Select again and will recommend to my friends.

bake element burned itself out.

  • Customer: Coral from Duluth, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy - I asked my husband to do it. He agreed that it was very easy. He unscrewed the old and took out the burned out part and inserted the new. Pretty much self explanatory. I wish all repairs were so simple. Thank you for having parts available.

broiler pan missing

  • Customer: RAYMOND from JACKSONVILLE, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ordered new broiler pan

Heating element went out

  • Customer: Jennifer from Arlington, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws on old element. Pulled element out to detach socket wires. With new element attached socket wires, pushed element all the way in and tightened screws.
All Instructions for the FEP310BW1
316-330 of 335