Models > FEFL68GMA > Instructions

FEFL68GMA Frigidaire Range - Instructions

All installation instructions for FEFL68GMA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEFL68GMA
31-45 of 471
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no display on display module

  • Customer: robert from orange CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 22 people found this instruction helpful
check for power in to the module,when it had incoming power,order new module,jnstalled it and walah done.

Large burner wouldn't heat

  • Customer: Phyllis from Elberon IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 25 people found this instruction helpful
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Burner failed due to poor manufacturing quality

  • Customer: LaVern from Cedar Falls IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 11 people found this instruction helpful
Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover. I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.

Broken glass interior oven door

  • Customer: stephen from garden grove CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 26 people found this instruction helpful
Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Bake element burned in 2 pieces.

  • Customer: Mary from Cabot AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Easy repair. Removed 2 screws and connectors, replaced . (Just a Note) Stove has been a lemon since purchased. Only 3 years old and have already had to replace timer, burners, oven door hinges, and oven lower burner. I'd have been better-off buying a good quality appliance in the first place. Have had many problems and finally replaced 3 year old Frigidaire refrigerator. Same quality issues. Replaced dispenser circuit, defrost circuit, then compressor. Lost a fridge full of food 2x. Under warranty but a real hassle. I will never buy another Frigidaire product.

Lens missing for burner "on" indication

  • Customer: Carol from Houma LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

oven element melted

  • Customer: Carl from Adams ND
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 9 people found this instruction helpful
Watched your video and quickly made the repair. I did have to remove the back of the oven (4 screws) to connect the electrical leads to the element. Frigidaire uses a wire harness that prevent you from pulling the wires into the oven to disconnect them as the video shows. No problem; a really easy fix.

switch not always turn off

  • Customer: Jerrold from San Marcos TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Replace cracked glass in main top

  • Customer: Cynthia from Plymouth MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
First I pulled the unit away from the wall and unplugged it. There are a few screws that hold the top in place - access them from the top/front/underside of the main top - pull open the oven door to get to them. Once these were out, I gently slid the main top forward. There are tabs in the back that fit in slots just under the control panel - just work them free as you slide. I slid the top forward enough to get past a narrow aluminum plate/tab (part #26B) in the very front that runs the width of the top. Once it's free of the tabs in the back, and the front is free, there is enough play in the wires & elements to move the top to one side of the stove and access the heating elements underneath. The heating elements are attached to brackets; the brackets (part# 26) are attached to the main top. You can leave the elements & wires attached to the brackets - there is one screw per bracket that attaches it to the main top - just remove the bracket screws. It requires either a square screw driver or a 1/4 inch socket. Do one side, then the other NOTE WHICH HOLE THE SCREW GOES IN, as there are a few to choose from. After the brackets were free, the top comes off. I moved the back tabs (part #18) from the old top to the new - NOTE THE ORIENTATION OF THE TABS. I didn't, and had to flip them over, after 20 frustrating minutes. With the new tabs in, I replaced the heating element brackets, then slid the main top back to its original position. If the tabs are in the right position (see above) it'll slide right into place. I had to work the narrow metal plate in the front under the main top with my fingers when sliding it back on. I replaced the front screws underneath, plugged it back in, pushed into place, and it's working fine. About 40 minutes total, extra if you don't note the orientation of the tabs in back, or the location of the element bracket screws. The oversized heating element won't let you put it in incorrectly.

Electric burner switch shorted out.

  • Customer: Armando G from Alice TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Bottom elerment burnt into

  • Customer: Danny from Gaffney SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 5 people found this instruction helpful
First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

broil element was bad.

  • Customer: William from Fort Myers FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Large burner would turn on high and not cycle off

  • Customer: Kevin from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

Bake element bad, broiler element OK.

  • Customer: Gerry W. from Oxford IA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

new switch was not wired like old one

  • Customer: PERRY from LECANTO FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 16 people found this instruction helpful
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.
All Instructions for the FEFL68GMA
31-45 of 471