Models > FEFL67GCA > Instructions

FEFL67GCA Frigidaire Range - Instructions

All installation instructions for FEFL67GCA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEFL67GCA
61-75 of 494
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bottom bake element went bad

  • Customer: James from Martinsburg WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Oven bake element was dead

  • Customer: Stephen from Spencer IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 2 of 3 people found this instruction helpful
Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

bake element burnt out

  • Customer: Kim from Union Grove WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

N/A

  • Customer: Dineshbhai from Rincon HWY21 GA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I had open back cover And remove the switch than replace new switch. Makesure cable conection.

Lower baking element would not heat up.

  • Customer: Jim from Harrison MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim

Oven wouldn't heat

  • Customer: KaShira from Wilmington OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

Heat element burned out.

  • Customer: Laura from Hurricane UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
The problem I ran into Was; Having the right socket size for doing the project. After taking care of that problem it was fairly easily to disconnect the element and reconnect the new one. It's pretty self explanitory.

Didn't Bake

  • Customer: Dale from Athens TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Took it off, ordered a new part and put it back on.
Ordered on Monday and got the part on Tuesday.

bake element burned out

  • Customer: Kenneth from Wantage NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.

Oven element broke in three!

  • Customer: Keri from Raleigh NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.

Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.

So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a

Replace the bake element

  • Customer: Michael from Fort Worth TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Had to remove the old element and had problems with the element shorted on the quick disconnect. After having my son unplug the appliance and cutting the quick connect off. My son then installed a new quick disconnect and the bake element.

While baking cookies I looked in the oven only to find the bake element was glowing white on the curve of the element, then a second spot started to burn. The element was fried.

  • Customer: Angela from Ruidoso NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You

bake element had stopped working

  • Customer: lynne from pelham NH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 1 of 1 people found this instruction helpful
My husband had recently moved out of our house so I was very nervous about trying this repair myself but it was actually very easy!!I ordered the part on Monday, it arrived on Wednesday and Wednesday night I was baking dinner in the oven!!

oven not heating up

  • Customer: raymond from irvine CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,

Banking Element needed replacement

  • Customer: Mitchell from Sebring FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 1 of 1 people found this instruction helpful
For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!
All Instructions for the FEFL67GCA
61-75 of 494