Models > FEF336ECE > Instructions

FEF336ECE Frigidaire Range - Instructions

All installation instructions for FEF336ECE parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEF336ECE
556-570 of 625
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element light staying lit

  • Customer: Russell from Glenmoore PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

Bake Element Broke

  • Customer: lance from Syracuse NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the two screwes that hold the element in place, unplugged the two electrical end points, plugged the new one in put the screws back in and the job was done.

Bottom drawer glide had snapped off

  • Customer: Joyce from Baytown TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was so easy -- took less than 15 minutes. I am a 75 year old woman and it was a snap!!!

Oven's baking feature stopped working

  • Customer: William from Paint Lick KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I use Youtube as a resource for instructional videos. It helps in most cases. This is as simple as you can get so probably not necessary for this repair. I unplugged the oven first. I unscrewed the the element brackets from the inside of the oven, pulled out the element until I could disconnect the wires from either end. I connected the new element to the wires and screwed the brackets to the back of the oven. I plugged the oven back in and tested the repair.

inner oven door glass broken

  • Customer: Cheryl from Derby NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Bake element burnt out

  • Customer: Benjamin from Lynch KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Two small screws removed from element frame,slid element out. With needle nose pliers, I slid terminals loose from element. Then I replaced the new element in reverse procedure. Quick delivery made things even better.

Burner would stay on and the hi-temp safety limit switch is all that would shut it off.

  • Customer: Dana from Acton ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.

Large element would only heat on high.

  • Customer: Roy from Kingsport TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

Bake element had separated and caught on fire

  • Customer: Kate from Eastsound WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I went to partselect.com, watched the video, found the part, but only after calling the phone number, and ordered on the phone. The part arrived within 4 days. I unplugged the stove, removed the racks, unscrewed the nuts at the back plates, pulled the element out, disconnected one side at a time, bending the wires so they would stay pulled out, removed the bad element, connected the new element, slid it back in the holes, screwed the nuts through the new plates, replaced the racks, plugged the stove in, and done. Very easy!

Broken Drawer Glides

  • Customer: Rob from Ballwin MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the helpful Video. Thanks.

Replace lower oven burner

  • Customer: George from Haughton LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I would have been able to effect the change-out in 10 minutes, but ran into a little problem. I knew that the connections were slip-on, so I tried to be careful not to pull too hard and disconnect them. However, I did not know that where the connection is made is at a 90 degree angle from the burner. So, not knowing this, I disconnected one of the electrical lines. Not good!. However, I figured it could not be too far from the hole, so I got a pair of forceps I use for my model railroading, and fished around an got a hold of it. Just be aware that the connection may NOT be straight line, and you will have to tip the burner up about to a 45 degree angle to get the connector and wire out. Next time I'll know!!!

Baking element quit working

  • Customer: Mimi from Hopwood PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I looked at the available online tutorial, followed the instructions given. It was an excellent tutorial and the repair was done in minutes. The element shipped quickly and the whole transaction was simple and cost effective!

bake element burned out

  • Customer: CHARLES from GEORGETOWN GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
was easy pulled out old one,pushed one hew one.

element blew up

  • Customer: Victoria from Alton IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I watched your repair video and this took no time at all, it was really easy. It took longer to find the right size socket and to clean the sides of the stove and underneath it after pulling it out than the repair took. Thanks!

Heating element went out in oven.

  • Customer: Jerald from Hackett AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unscrewed two screws and unplugged the two wires took the old element out and replaced it with the new one plugged the two wires back in put it back in place and put the two screws back in place and I was done in less than 15 minutes.
All Instructions for the FEF336ECE
556-570 of 625