FEF336ECC Frigidaire Range - Instructions

I watched the video that was posted on the parts website when I ordered my part for my oven and it was sooooo simple now I'm back to cooking and my part was to my door in1 day after I order would definetly use this company again.

Used a nut driver to remove old bake element and removed slide on clips on each side took the old pieces to trash and the put new element in by installing slide on electrical connection the tightened up screws with nut driver it was easy and the best thing was ordering of the part and getting the correct part in a timely fashion. I wish all websites were this efficient.

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Turned the main power off to my oven. Got my part removed two screws took the old bake element out put the new one in, replaced screws, turned power back on and boom it was fixed. Thanks so much for making it so easy.

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

Removed two screwa holding element in place. Removed the connecting wires. Attached wires to new element. Reset emlement, replaced the screwa and I was done. Actuallt, I did as exactly as indicated in your film discribing the installation. P.S.-Part arrived in two days inspite of the impending hurrican. Extremely satisfied.

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

My wife had seen a small fire in the bottom right of our oven, and I quickly turned off the oven unit, which put out the fire. We tested the oven a couple more times after it had cooled and determined that indeed the bake element had burned out. I'd used PartSelect before and been very pleased with their service (speed, ease of use of site, etc.,etc.) so I ordered a new bake element, which arrived in two days! It was easy to replace: I turned off the circuit breaker, slid the oven out from the wall, disconnected the plug, and then got to work undoing the tabs that hold the bake element to the rear wall. The only little glitch was that the screw heads on our range were neither slot nor Philips - they turned out to be small square-socket screws. I couldn't see that until I turned a bright flashlight on the job. Then it was a simple matter of trading out the screwdriver bit, disconnecting the old element, plugging in and attaching the new one, and away we went. Oven as good as new! Thanks, PartSelect!

followed the video provided and installed it as instructed. Video and instructions provieded were very helpful

Remove bolt from both ends of element carefully as not to damage wires connected to the ends. Replaced with new element. Simple.

It took about 3 years to order and 3 minutes to fix. forgot to turn off "easy" video on conputor. Wife watched was mad........... for taking so long to fix. 41 years married, any video to fix wife and get me to 42 years as easy as changing draw glides? Thanks Jon

After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!

Turned off electric at breaker box for range. Using a socket wrench from my little pink tool kit, I removed the two screws holding the unit at the back of the oven. Gently pulled each side of the unit out, exposing the terminals. Holding with one hand and wiggling the terminal with the other, removed the element. One was very easy, but the other was harder. Next I connected the new element to the terminals. Gently pushed the terminal back into the oven wall and replace the screws. Last turned the electric back on and then turned the oven on. The video that was online was very helpful.