Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FEF336ECC > Instructions

FEF336ECC Frigidaire Range - Instructions

All installation instructions for FEF336ECC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEF336ECC
31-45 of 632
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Element shorted out

  • Customer: Patrick from Louisville, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 19 of 22 people found this instruction helpful
I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

Broken bake element

  • Customer: Chris from DeRidder, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 19 of 23 people found this instruction helpful
From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.

missing oven racks

  • Customer: ALLAN from APACHE JUNCTION, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 20 people found this instruction helpful
order pcs fit perfect.

Front Burner was on high all the time when on

  • Customer: Gregory from Monument, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 17 of 19 people found this instruction helpful
Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.

Element caught fire when i preheated my oven

  • Customer: Michael from Union City, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 25 people found this instruction helpful
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

Element burnt out

  • Customer: Larry from Danville, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 17 of 21 people found this instruction helpful
The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.

Went to use the stove and the main baking element had a melt down.

  • Customer: Tracey from DEVILLE, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 19 people found this instruction helpful
shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

Neither of the oven elements worked (bake or broil)

  • Customer: Jim from Frankfort, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 16 people found this instruction helpful
Turn off the circuit breaker to range. Removed the back panel using a nut driver. Removed color coded wiring from old clocktimer and placed wiring on new clocktimer. Removed old clocktimer from range using a phillips screwdriver. Removed the white clock face using a utility knife, placed the white clock face on the new clocktimer. Installed new clocktimer in range using a phillips screwdriver. Replaced the back panel using a nut driver. Turn on the circuit breaker. Set the range clock to the correct time. Baked some cookies to test oven. Easy as pie :)

new switch was not wired like old one

  • Customer: PERRY from LECANTO, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 17 of 28 people found this instruction helpful
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

Connection to surface element was broken

  • Customer: javier from oceanside, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 16 of 25 people found this instruction helpful
I went all the way around the unit and removed screws holding top of unit in place. Removed knobs holding front panel in place. Remove control panel. top should come off. Remove screws attaching element top and metal frame. Undo bracket and remove element. Disconnect wires. Remember where they were attached.
Replace element and reverse steps.

the oven wouldn't work, but the range elements did

  • Customer: clinton from Columbia, MO
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 12 of 17 people found this instruction helpful
it was an easy repair, and i thought it was the clock /timer, but it was the probe.

One element in a glasstop range would not engage

  • Customer: Kwok from Silver Spring, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 11 of 15 people found this instruction helpful
All of a sudden, one element in our glasstop range would not light and heat up. My wife and I were not sure what to do. Looked it up on the internet, found that you can do it yourself as others desribed the process of accessing the elements below. We decided to do that. It takes two people as one is holding up the glass because it opens like a car hood. While we diagnosed it was not a wiring issue (found a burnt wire, rewired the burnt wires (after mending the non burnt portions) to another element. The element that was not working before still did not turn on. Decided to purchase an element. While many online places sell elements, PartSelect actually allowed searching by brand with exploded views of the range to select the exact parts. This lessened the worry of purchasing a wrong element. When the part came (almost one day later), the repair was less than five minutes. Thank you PartSelect. I feel I saved a lot of money and aggravation.

In a seasonal house, a mouse got into the oven insulation during the winter. We have gotten rid of the mouse but when we used the oven we could smell mouse urine! Upon inspection we could see that the mouse lived and urinated in the oven insulation.

  • Customer: Susan from Newington, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
My husband removed the screws that held the top of the stove on and then lifted the top up. It is hinged. He then took out the old insulation, wiped down all visible parts of the interior with a bleach solution and replaced the blanket insulation with the new insulation. That took care of the problem!

unit lost digital display, wouldn't control oven

  • Customer: Thomas from St. Petersburg, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 16 of 32 people found this instruction helpful
First I weighted out weather it was better to repair the unit or relpace it with a used one. The stove was in good condition so a small investment of $140.00 was a no brainer, repair went off smothly once I found your web site and could see the parts I needed for the repair, also realy enjoyed the timely manor in which I received the parts, Thanks. Tom

Front Right Radiiant burner was damaged

  • Customer: Rashiklal from Marietta, GA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 10 of 15 people found this instruction helpful
Followed the instruction printed on the page, while ordering the part.
All Instructions for the FEF336ECC
31-45 of 632