Models > FEC9X6XEBA > Instructions

FEC9X6XEBA Frigidaire Cooktop - Instructions

All installation instructions for FEC9X6XEBA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEC9X6XEBA
1-7 of 7
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burned out burner

  • Customer: Lori from Winter Haven FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 31 of 39 people found this instruction helpful
First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

rf burner was not working

  • Customer: Neil from Jessup PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 25 of 33 people found this instruction helpful
First I removed 2 screws that held the stove top in place. Raised the stove top and support it. Then, I removed the hold down spring for the burner and removed three wires from the old burner. I found that the connector on the white wire was spread open too much so I crimped it closed for a better fit on the terminal. I reattached the three wires, put the hold down spring back in place, lowered the stove top and installed the 2 screws. JOB DONE

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 9 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

Burner eye would only produce High Heat on all settings

  • Customer: scot from keller TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 18 people found this instruction helpful
Ordered a new Surface Burner Switch to replace the failed unit.
When I opened the burner lid, I could see the insulation on all the wiring for the burners had fallen apart and wiring was exposed. The wiring for all 4 burners was exposed as the insulation had deteriorated and fallen off over 80% of the circuits. It was just blind luck there was not a fire or an electrical failure on a grand scale. I replaced the wiring and burner connection assemblies as they also showed signs of age and deterioration.
Had the switch not gone bad, forcing me to look into the wiring assemble, there very likely would have been an electrical fire. In a 220 volt appliance, electrical fires are a lot more excitement than I need.

Scot Hooper
Keller Texas

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Element would not heat up

  • Customer: Everett from Colchester CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
All Instructions for the FEC9X6XEBA
1-7 of 7