Models > FEC30C4ABD > Instructions

FEC30C4ABD Frigidaire Cooktop - Instructions

All installation instructions for FEC30C4ABD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEC30C4ABD
1-15 of 15
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner would consistantly go to high no matter where the dial was positioned.

  • Customer: Gary from Herrick IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
First I unplugged the stove.Removed the upper control panel back (10 phillips screws). Removed the plastic dial( pulls straight off). Removed the 2 screws behind the dial that is holding the switch in the control panel. Took one wire at a time off the old switch and put them on the new switch according to each electrical spade marking. L1, L2, H1, H2 and P. Installed the new switch in the control panel securing it with the 2 screws. Installed the dial, installed the upper back panel using the old screws. Plugged the stove back in and tested it.
Note: My new switches shaft was 1/8 of an inch longer so it does put the dial a little further away from the control panel. Wife says: It's OK, don't worry about it.

One of the switches on my stove had quit exept for High. every level on the switch was high.

  • Customer: Marilyn from Lafayette GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
First I removed the 2 screws that held it in place.
Then I took te screws out of the backguard cover and pulled it down so that I would get to it. Then I unplugged the wires, and replugged them on the new switch, then screwed it back in to the range, then put all the screws back in backguard cover, and plugged the range back up and put it back in its place. It was real easy.

PITTED, ERODED DRIP PANS

  • Customer: Josephine from Malden MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
1. FIRST I PULLED OUT THE HEATING ELEMENT FROM STOVETOP AND REMOVED OLD PAN (NO SCREWS) VERY SIMPLE.

2. PUT NEW PAN IN AND INSERTED THE HEATING ELEMENT BACK IN PLACE.

Renewed drip pans

  • Customer: Frank from Winter Garden FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!

rusty bowls

  • Customer: Monty from Kenton OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
very easy

Needed new drip bowls.

  • Customer: Robert from Oradell NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

Drip Bowl Replacement

  • Customer: Jennifer from Arena WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I could not find the larger size universal drip bowl to fit the 8" burners on my stove. This product replacement is perfect.

Couldn't find drip pans that fit

  • Customer: Heather from Springfield TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I went to all of the do-it yourself stores and spent a bunch of money on aftermarket drip pans only to find out that none of them fit. I came up on your website and also called customer service. The found the right part and mailed it too me. They fit perfectly. No more burnt and rusty drip pans. I know where to go for parts now.

Replace ill-fitting drip pans

  • Customer: thomas from cleves OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After two failed attempts to get the 'correct' drip pans for my range from two other supply outlets, Part Select had the proper drip pans for this model. They fit perfectly! Simple installation and threw away those cheap, poorly fitting replacement pans I've put up with for three years! Thanks Part Select for having the correct parts!!

Replace drip bowls and knob.

  • Customer: Teresa from Modesto CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
No tools needed - the delivery of the items was real fast.

Surface Burner would not get hot

  • Customer: Keith from Hazleton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pull out the old one. Plug in the new one and your good to go.

needed new element

  • Customer: Olive from Rochelle IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled old out put new in.

Replaced burner drip bowl

  • Customer: Irene from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to remove the old drip bowl and replace with new ones.

The switch to the large right burner went out.

  • Customer: Patricia G from Stewart TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Our neighbor, who is an electrician, watched the video on how to install. Since this switch was substituted, he paused the video several times to see how the wires should be attached. It worked.

Unable to control surface burner temperature

  • Customer: Vista M. from Northport AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pull range unit from wall. Disconnect power cord. Remove back panel on range(10 Phillips head screws). Pull knob from surface burner switch and remove two screws. Remove and re-connect wires from switch by number on switch. Replace switch and back range panel. Re-connect power cord and re-position range to original spot.
All Instructions for the FEC30C4ABD
1-15 of 15