Models > FEC26C2AQD > Instructions

FEC26C2AQD Frigidaire Cooktop - Instructions

All installation instructions for FEC26C2AQD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEC26C2AQD
1-15 of 23
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Block terminal burnt out, hot plate not working, needed to replace the terminal block

  • Customer: Shaun from Whitehall MD
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.

Burner wouldn't stay hot.

  • Customer: Billy from Lovelady TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
I pulled out the old element and the new one just plugged right in.

Two of the rangetop controls would intermittently go to hi-heat

  • Customer: L E from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
The left rear (small burner) was the first to start intermittently having only off or high heat. Then the left front (large burner) started (probably sticking contacts). Since two had gone bad, I ordered 4 new ones to make a complete repair. I was pleasantly surprised to discover that the large burner controllers had been "beefed up" to a heavier duty controller. The changeout was merely removing wires and verifying terminals on the new controllers. It was so easy that "even a caveman could do it"

replacement burner

  • Customer: Donna from Westfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery

Enement was blew out.

  • Customer: Chhabildas from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 4 people found this instruction helpful
I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

PITTED, ERODED DRIP PANS

  • Customer: Josephine from Malden MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
1. FIRST I PULLED OUT THE HEATING ELEMENT FROM STOVETOP AND REMOVED OLD PAN (NO SCREWS) VERY SIMPLE.

2. PUT NEW PAN IN AND INSERTED THE HEATING ELEMENT BACK IN PLACE.

Needed new drip bowls.

  • Customer: Robert from Oradell NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

element had been damaged

  • Customer: Merle from Towanda PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Renewed drip pans

  • Customer: Frank from Winter Garden FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!

rusty bowls

  • Customer: Monty from Kenton OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
very easy

Left rear burner had a damaged burner prong.

  • Customer: Jackie from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
I just had to plug the new burner plate in the receptical
and it works again very well.

old element worn out

  • Customer: Janet from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old element and plugged in the new. Very simple and easy. Shipping and delivery was amazingly fast!

Drip Bowl Replacement

  • Customer: Jennifer from Arena WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I could not find the larger size universal drip bowl to fit the 8" burners on my stove. This product replacement is perfect.

Surface Element burnt out

  • Customer: Vicki from Strong ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Lift stove top cover up and support cover so it will not fall down unplug element put new one in close cover and turn burning on and watch the burner get red hot. simple job why call a repair man in. Vicki

Couldn't find drip pans that fit

  • Customer: Heather from Springfield TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I went to all of the do-it yourself stores and spent a bunch of money on aftermarket drip pans only to find out that none of them fit. I came up on your website and also called customer service. The found the right part and mailed it too me. They fit perfectly. No more burnt and rusty drip pans. I know where to go for parts now.
All Instructions for the FEC26C2AQD
1-15 of 23