FDB750RCS0 Frigidaire Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replaced rusty upper dishwasher rack
Took less than 10 minutes. It took longer to order the part than install it. Great company, ordered on a Saturday, had the part on Wednesday.
Parts Used:
-
William from Cocoa, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaking
-
Joe from Garrison, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher leaked around the door
My Son used needle nose pliers to remover the old gasket, then starting on the lower right side, inserted the new gasket and used the rounded end of handle of a wooden spoon and pressed the gaste in place by running the handle up and around the top then down the left side. Used sissors to cut the new gasket to length. Door fit very tight. Ran a normal wash cycle and no leaks.
Parts Used:
-
Clarence from Gerald, MO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would leak front left corner
took out screws around door, took off hinges, slip new seal in put hinges back on screws around door. does not leak
Parts Used:
-
Jacob from nappanee, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
latch broke and would not close properly to run the dishwsher
the latch and gasket came 2 days after I ordered the part. the repair was very simple and only required taking a few screws out, attach the four plugs and put back together, very simple and very pleased with how quickly the part arrived!
Parts Used:
-
Lori from Breinigsville, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Main Soap dispenser lock is broken
Unscrew all the scews arround it. Use tape to hold the eletronic panel. Remove the metal cover.
Remove the 6 screws around the dispenser. Replace the new one. Put the metal cover back first. Put back the electronic panel at last. Done
Remove the 6 screws around the dispenser. Replace the new one. Put the metal cover back first. Put back the electronic panel at last. Done
Parts Used:
-
Quan from Spingfield, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch broken, Upper and Lower racks rusted
I disconnected power to dishwasher. I removed six screws to gain access to door latch assembly. I removed two screws, which attached door latch to machine. I removed the 4 electrical attachments.
I then attached 4 electrical attachments to the new door latch. I attached new door latch to machine with two screws. I reattached cover with 6 screws.
I connected power back to the dishwasher and everything worked great.
Took aprrox. 15-30 mins to compete.
It only took three days to received shipment including day I made purchase.
I was very pleased with my purchase.
I then attached 4 electrical attachments to the new door latch. I attached new door latch to machine with two screws. I reattached cover with 6 screws.
I connected power back to the dishwasher and everything worked great.
Took aprrox. 15-30 mins to compete.
It only took three days to received shipment including day I made purchase.
I was very pleased with my purchase.
Parts Used:
-
Marc from Green Brook, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken latch handle
TURN OFF ELECTRICITY TO DISHWASHER FROM FUSE BOX! Remove top 6 screws from inside the door panel. Once you have access to latch, remove the two screws that hold it in place. When removing the four terminals use firm grip and remove them as gently as possible. Reposition terminals on the new leads paying close attention to their location. Black wires on one side and white wires on the other. "L" shaped leads are in front and rectangle leads are in the back. Use the two screws to reattach the new latch, replace the door panel and you are finished.
Parts Used:
-
Edward from Spring, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The handle was broken
I replaced the old handle by taking out the six screws that hold the control panel on, then removed the two hex screws that held the handle in place. I removed each wire (4 total) one by one simultaneously reconnecting them to the new handle. Then I replaced all screws as they were and called it a day. Pretty simple, little mechanical knowledge required.
Parts Used:
-
John from Dayton,, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch handle broke.
Unscrewed the top of the door assembly that holds the latch. Unfastened and pulled the old latch and switch assembly then refastened. Done.
Thanks for being there PartSelect.com !
Thanks for being there PartSelect.com !
Parts Used:
-
John from Labadie, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
handle broke
Removed 6 screws that hold control panel to door and removed 2 torx screws and 4 wires on latch assy.reverse order to install new latch assy.Part arrived in 3 days.Great service,if I need any other parts in the future I will definetly use PartSelect.
Parts Used:
-
David from Wareham, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken spring
Dealer/repairman could not get the spring, told wrong model #, after 2 weeks I looked on line with the same model #, which is my model #. Found Part Select.com, ordered on Thursday about 3 p.m., rec'd the next morning at 9:38 a.m. Great service, easy web site. Was very impressed with Part Select.com and I will recommend you to anyone I know who needs appliance parts.
Parts Used:
-
Marla from Jesup, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The interlocking door latch gave up the ghost, at first, I thought it mighthave worked loose. but an inspection showed that the part had broken. I went onlinein the a.m. using the mfg. and part description, found part select.com and ordered the part. By the next day it was delivered (ordinary groun
I removed the screws holding the cover in place. used my digital camera to note the wire connections. Then , shut off the power to the unit. Using the torx driver I removed and replaced the broken unit(two screws). It was a perfect fit. I checked the wire photo to reattach the leads . Before tightening the cover in place, I checked the latch for fit to its mating part on the machine. Then I replaced the screws, made them tight using a portable drill with a clutch. Turned on the power and the repair was complete. Very quick, simple and I saved a bunch of money. Thanks!
Parts Used:
-
Fred from Lady Lake, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower rack rollers were missing
Rollers just snapped on the diswasher rack. Took just seconds to do.
Parts Used:
-
Kathy from Greer, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door spring
-
Dianne from Bellingham, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!