Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB750RCC0 > Instructions

FDB750RCC0 Frigidaire Dishwasher - Instructions

All installation instructions for FDB750RCC0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FDB750RCC0
61-75 of 531
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leak underneath dishwasher

  • Customer: Richard from New Orleans, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 9 of 10 people found this instruction helpful
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Dishwasher Leakibng

  • Customer: Eric from Benton, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench (Adjustable)
  • 9 of 11 people found this instruction helpful
Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks

Heater Element Covered in Mineral Deposits

  • Customer: Chad from Cypress, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 14 people found this instruction helpful
Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a few weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.

Water leak behind kick-plate

  • Customer: Larry from EDWARDS, CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 10 of 15 people found this instruction helpful
Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

dispenser cap latch broke

  • Customer: Michael from Moreno Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the door, facing inside. The bottom screw on each side. Thanks for all the help.

water leaked from the center of the door

  • Customer: Bradford from Secor, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

Broke nubs off of stem when cleaning

  • Customer: Glen from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).

My dishwasher was leaking

  • Customer: Vincent from CORAM, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 10 people found this instruction helpful
This was too easy. I pulled out the bottom rack, spread apart the two clips which are at the bottom of the spray arm with my fingers and pulled out the old broken spray arm. The damage was visible. Then I took the new spray arm ( which looked different but still fit nicely) and gently pushed it into place. Done!

Upper rack not being cleaned

  • Customer: steven from Walnut Creek, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 11 people found this instruction helpful
This was pretty easy. It was a guess as to the problem, but there much debate , if the water isn't moving it had to be the pump, right?. So i replaced the circulation pump. 2 screws on the top and two trim screws on the bottom, and it slides right out. Then UNPLUG IT.. Take the screen out of the bottom on the inside and make sure you get all the water out or it will end up on the floor when you tip it on it's side. The directions were ok, i looked over them briefly but didn't use them. tools were, phillips srewdriver, torx driver (pump bracket srews) wire stripper/crimper (for the plug adaptor) and a heat gun, (for the heat shrink tube for the crimp connection). Overall it was pretty easy. the pump was made to be easy to replace. 45 min and back in action.

Dishwasher was leaking out of small gold nut

  • Customer: Emily from Kyle, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 7 of 9 people found this instruction helpful
The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

Replaced the Drain Pump

  • Customer: Kyle from Jackson, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 15 people found this instruction helpful
Unplugged the dishwasher and pulled it out. Tipped it down on its side. Removed the old and replaced the new. Re-installed and replugged it. Ran a test. Checked for leaks.

Water coming out of motor/motor really loud noise

  • Customer: David from Cragford, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Took the dishwasher out removed the two screws and the part holding the motor in and removed the motor. Received the parts, places o'rings on the motor, which came with the kit, even though I ordered the two o'rings. Replaced the motor, installed the part that holds the motor and tightened the screws. Cut the old connector off the dishwasher and replaced it with a new connector that came with the kit. Reinstalled the dishwasher, works great. Thanks for your Site.

leaking dishwasher

  • Customer: Mark from port matilda, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

Replace sump gasket

  • Customer: Greg from Rockwall, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 11 of 21 people found this instruction helpful
#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Bottom spray arm got stuck and melted

  • Customer: Thomas from Ebensburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
First I removed the bottom dish rack to gain access to the spray arm. I proceeded by pulling straight up on the bottom spray arm, it disconnected with gentle force. The replacement part was not identical, so I determined that it would work by inspecting hole patterns and heat shield configuration. Then I gently pushed the new spray arm onto the water supply tube making sure that the spray arm snapped into place. Due to extremely fast ground shipping (less than 20hrs from order to my door) the repair was done within 24 hrs! Boy...was my wife pleased!
All Instructions for the FDB750RCC0
61-75 of 531