Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB125RHB2

FDB125RHB2 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for FDB125RHB2

If you know the dishwasher repair part you need, you can browse the list of all parts on the FDB125RHB2, or you can search by name or part description. You can also find your part by where it is located on the FDB125RHB2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for FDB125RHB2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

$14.92

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

$26.08

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$29.30

Lower Spray Arm - Gray

This part comes with the heat shield and the tower. It is located on the lower half of your dishwasher. Water is forced through this spray arm by the pump and motor assembly. The water from the spray arm is meant to spray water and detergent forcefully over the dishes. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. If the spray arm is made of plastic, it can become warped or cracked. If it is a metal spray arm, it can pull open at the seams or get bent. To check your spray arm, make sure the spray arms can move freely on their bearing rings and mounting brackets. Remove your spray arm and check to ensure it is straight and undamaged. Check the holes and clean them if they are clogged. Cleaning out the holes can be a tedious task, so consider replacing clogged spray arms. NOTE: Clogged holes are a hint to check if there is a problem with the filter system that resulted in debris coming into the arms in the first place.

$3.63

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the he...

$39.42

Door Latch and Gasket

Black in color. No longer available in almond. This door latch prohibits the dishwasher from operating when the door is open. The gasket is used around the door to keep the dishwasher from leaking.

$19.78

Door Spring

This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the...

$52.38

Detergent and Rinse Dispenser with Cap

This detergent and rinse dispenser with cap may also be known as the dishwasher dispenser assembly and is a part for your dishwasher. The function of this part is to attach to the inside door panel of your dishwasher and hold the dishwasher detergent and rinse in a closed compartment. The manufacturer has redesigned this part and although it may appear different than the original, it will have the same functionality, which is to release the detergent and rinse aid into the dishwasher. To complete this installation, you will need a Phillips screwdriver, and a pair of needle-nose pliers.

$20.41

Door Strike

This door strike is mounted to the top of the dishwasher cabinet. This part catches the door handle to keep it closed.

$20.41

Spring Linkage

This linkage attaches to the door spring.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from Inlet Valve

  • Customer: CHRIS from ROANOKE, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 566 of 577 people found this instruction helpful
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first ... read more

Lower Rack Roller Missing

  • Customer: Sandra from Mount Vernon, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 365 of 367 people found this instruction helpful
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new. read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 141 of 154 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more