Models > FDB1050REC2 > Instructions

FDB1050REC2 Frigidaire Dishwasher - Instructions

All installation instructions for FDB1050REC2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FDB1050REC2
316-330 of 463
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

standing water after done, poor rinse, dirty dishes.

  • Customer: Tucker from Woodward PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
unscrew top tabs of dw pull out,,unplug.. bail out water..disconnect drain and water at house connections..turn dw on it's side and unscrew old pump..ply off connectors..install new pump..bam!!

Dishwasher did not drain

  • Customer: Jason from North Little Rock AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I turned the power. Unhooked the dishwasher and flipped on the back exchanged drain pump. Perfect. Works like charm.

Lid on detergent dispenser wouldn't stay shut

  • Customer: Katherine from Fortville IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Found breaker switch for dishwisher and turned it off. Removed one screw on each side of bottom of door. Front panel slid off. Removed the two wires on dispenser, then took out the six screws. Pulled entire piece out from the inside of door. Put in new dispenser, attached wires (white on inside and red on outside). Put in the six screws and including the one with the little hook that holds the wires. Slid the front door panel back on and replaced the two screws (one on each side of bottom of inside door). Flipped the breaker switch back on. Approximately 25 minutes. Very easy, thanks to the person who wrote his/her instuctions previously.

The cap fell off and was melted on one side--therefore the rinse solution kept draining out.

  • Customer: Nancy from Williamsville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was determined to find and replace the part myself. Much to my surprise, others had had the same problem! Thanks to the reviews on this website gave me the "courage" to do it myself!

My dishwasher was leaking from and electrical connection at the heating element

  • Customer: Kevin from Old Orchard Beach ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

Brass Nut Cracked - Water Leaks O Floor

  • Customer: Robert from Oak Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!

Leaking water

  • Customer: Patrick from Knoxville IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced bottom gasket, still leaks. This was not the problem. Will have to keep looking for source of water leak. Bottom gasket installed really easy. Just pulled the old one out and inserted the new. Just was not the source of leak.

Spray arm melted to element!

  • Customer: Mary from St Marys GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
As a property manager in a small town it has been difficult to find adequate appliance repairmen. Being able to order the parts online and allowing any of my handymen install is a hugh relief. This has been a great ordering experience

Leaking at the door

  • Customer: John from Hammonton NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just pulled the old one out and installed the new.

lower rack was rusted and vinyl covering was coming off

  • Customer: Robert from Kannapolis NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
new lower rack was perfect fit, roll the old one out and roll the new one in.

Tips on rack were rusted and leaving marks on my dishes.

  • Customer: Patti from Houma LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
everything went great. Just took out the old and put in the new. No problenms at all. I will be referring your company to everyone I know, Soon to be ordering part for my refrigerator, it's about 10 years old.

The diswasher racks were rusty, rubber falling off.

  • Customer: R from Sun City West AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed racks and replaced them. Didn't need tools. Easy Peasy!

Water inlet valve leak

  • Customer: Marshall from Newnan GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Repaired with installation instructions from PARTS-SELECT. Worked perfect!

dishwasher door was leaking.

  • Customer: Dean from Boscobel WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out the gasket,trimmed the gasket to fit and alittle pressure to put.it in place, very easyto do. No worries any one can do this and savek yourself costly repair person.

Leaky inlet valve

  • Customer: Lance from Chandler AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Cakewalk, replacing a water inlet valve is self-explanatory. Take the old one off, put the new one on .. that's pretty much it.
All Instructions for the FDB1050REC2
316-330 of 463